How to pull the cartridge from the printer: Samsung, Canon, HP, Brother

Although we want, but it is not always possible to avoid collisions with the internal equipment - and it usually concerns printers. This office miracle can knock on paper, leave a bliss on the printed document, disconnect from the computer or spend all the paint in the cartridge. Cartridges will have to change in any case, but sometimes it is quite difficult to do it.

Let's figure out how to just pull the cartridge from the printer.

How to pull the cartridge from the printer
How to pull the cartridge from the printer

When you need to pull the cartridge from the printer

The reasons for extracting the cartridge may be several.

Firstly if paint ended. The printer will warn you about it in advance when the lack of paint does not yet affect the quality of the print, but then the color reproduction will begin to deteriorate, the black paint will begin to flex and will eventually pop up the corresponding error.

Secondly If the device gives an error, although no warnings appeared. In this case, it may take a simple reinstallation of the cartridge into the system, but sometimes you have to replace the chip or calling a specialist.

Finally If the printer flashed the paper, left on it incomprehensible divorces, blots and other strange traces.

Types of printers and cartridges

Basically, two types of printers are dominated on the market: laser and inkjet. Monochrome laser printers often use one large block, in which parts of the printed device and tank container (coloring powder) are combined. Colored printers often use different cartridges with black, red, blue and yellow colors. In jet printers, the cartridges often look like transparent plastic containers with liquid paint.

General recommendations

  • Safety must be followed. Before interfering with the system, remove any decorations from hand: rings, bracelets, gloves and everything else that can catch the mechanism; Slide the sleeves.
  • Determine what printer you have. Inkjet printers often require inclusion (otherwise the cartridges will be difficult to remove), laser - on the contrary, disconnect from the network.
  • Open the lid and find the cartridges. They are easily determined by paint (where the capacity is transparent) and special marks: C, M, Y - for color cartridges (sometimes used simply C), for black - k or b; Also common marking of colors numbers.
  • Pull the paper from the printer before removing the cartridge.
  • Do not use gross power - everything can be inserted without it if you use the right levers.
  • Be careful with laser printers - they heat the thermofixer. It is best to wait ten minutes after turning off the printer so as not to burn.
Any printer is simply nowhere without paint, which ends very and very quickly. In addition, each type of printer has its own characteristics in recharging the cartridge. Read, How to independently fix the inkjet cartridge or laser printers .

How to get a CANON printer cartridge

In the canon jet printers type PIXMA (MP250, TS9540, etc.) the process of extracting the cartridge looks quite simple.

  • Run the printer and wait until the device boots.
  • Opening the lid, secure it and wait until the carriage with cartridges stop. The place for which you need to pull is specifically allocated, and, as a rule, is under the scanning part.
  • Raise the clamp (or detect the tongue), holding the cartridge, and smoothly pull it out of the groove.

It should be borne in mind that some printers (Series G) have an uninterrupted ink supply system and there is no need to change the cartridges, they are just enough to fill through special compartments.

In the case of laser printers like Canon LBP, everything is even easier.

  • Disable printer.
  • Open the lid.
  • Pull over a special handle on a cartridge that will allow you to pull it with minimal effort.

The only confusion may occur when searching the cartridge, but, as a rule, there is a special paper sticker with the word "Cartridge" - the handle is under it.

How to pull the cartridge from the printer samsung

SAMSUNG M2070W / MLT-D111S Laser Printers Type:

  • Disable from the network.
  • Open the main cover
  • Decorate the fastening with the front of the printer and open the second cover
  • Smoothly pull the handle under the word "samsung"

Printers type CLX cover in front of cartridges is right on the front side. Opening it, you can see several lamellar cartridges with color stamps nearby. You can simply remove them by pulling themselves.

How to remove the hp printer cartridge

Similarly, the black and white laser HP refueling occurs

  • The device is de-energized
  • The printed block is rising (above the department where printed paper is served)
  • The panel separating the compartment with the finished sheets from the cartridge is rising, if the cartridge is not yet visible
  • Carefully removed the cartridge for the plastic handle

Inkjet models such as Deskjet or Officejet are refilled just like Canon Pixma:

  • Printer turns on
  • Opened cover top of the printer
  • After stopping the carriage with cartridges, click on the latch tongue and smoothly pull out the cartridges moving up.

Some Deskjet have a special hole under the lid, which allows you to change cartridges even without turning on the printer.

How to remove the cartridge from the brother printer

Brother's laser printers operate about one principle.

  • Printer is better to turn off.
  • The cover in front of the cartridge is somewhere under the control panel (buttons and empty). It opens upon itself.
  • The cartridge along with the climb is lifted and pulls out. Some printers happen a mechanical failure and the clip just do not pull it out. In this case, you need to find a small black hook on the side (most likely to the left) and pull it on yourself. After that, the cartridge is pulled out.
  • After that, pull out the cartridge from the drum by holding the blue button.
  • Next, insert the cartridge to the drum and put it back to the printer.

Inkjet Brother Series MFC J have a special department for cartridges on the side of the right. As a rule, it is on the right and the name of the company and the type of cartridges is written on it.

  • Turn on the printer
  • Open the cover
  • Click on the holder over the cartridge. He must get up in a clamped position.
  • We calmly get the cartridge and insert a new one.

There is a small number of printers in which the handle is attached not to the very cartridge itself, but to the clip for it. As a rule, these are colored laser printers of other firms (Ricoh, Epson). However, after extending the clip from the printer, all actions are similar to those described.

If you want to replace the cartridge, the procedure can be performed independently. Consider how to do it right, as well as we will analyze the highlights of the selection of consumables and work with them.

Replacing the cartridge in the printer: how to insert a new

Replacing the cartridge in the printer

How to determine that the cartridge should be replaced

It is possible to determine that the old cartridge is worn and the installation of a new element is required by such signs when printing:

  • The formation of white vertical or horizontal stripes on a sheet. In the laser devices for a temporary solution of the problem, you can slightly shake the consumility, in the jet models you need to immediately change it.
  • Not all letters are printed, there are no words completely, not visible text at the edges of the sheet.
  • Gray tone text fuzzy.
  • There is no one of the shades or color reproduction, does not coincide with the original.
  • The device "Replace toner" appears on the device display. Usually the function is available in more expensive models equipped with a special chip (although some manufacturers install a chip for all their products). The message appears in advance when a little dye remains in the consumility.
Replacing the cartridge in the printer: how to insert a new

Replacement warning

Choosing a new consummer

The cartridge that is located in the printer when buying has a feature ever end. By the way, the hint, how to change the cartridge, can be found in the instructions for equipment.

To select you need to consider such moments:

  1. What printer is used: inkjet or laser. Cartridges for two types of equipment are different. In the first case, this is a small element of 7-10 cm long, in the second - length of about 30 cm.
  2. Write down the number and brand of the product specified on the old consumator housing. This will make it possible to find a new cartridge. You can also choose from the brand and model of the printer.
  3. Resource. What it is more, the longer it will not be replaced. Typically, the indicator is specified with the calculation that the page will be filled with 5% paint. Inkjet models with monophonic inks have a resource up to 100 sheets with black fonts, options with multi-colored paints - about 30-40 sheets. Laser monochrome devices have a cartridge resource up to 1500 sheets.
  4. If you do not want to buy expensive original dyes, you can choose budget substitutes that there are many firms. However, when purchasing it is important to focus on the quality of the product of a particular brand (so as not to buy a toner of low quality).

About how to select a cartridge for the HP printer, you can see in this video:

Cartridge replacement procedure

First stage: Remove the old cartridge

Installing the cartridge begins with the removal of an old element installed in the printer. Procedure:

  • Turn off the printer - this is a mandatory security requirement.
  • Open the lid in the housing where the module is located. Be careful when opening a laser printer - the lid can be hot.
  • Remove the element. Sometimes it is attached inside with several clamps. Begroof them and carefully pull out the element. Some printers have a special lever for easy extraction.
  • If the consumator is not pulled out (stuck) Do not try to extract it with force. Contact your service, otherwise you can damage the equipment.
Replacing the cartridge in the printer: how to insert a new

Extraction of the old cartridge

Second Stage: Preparation of a new cartridge

You can only install that block that corresponds to the equipment brand. It can be an original element or products of other manufacturers, which is suitable for a specific model.

A new cartridge is smeared in a hermetic box. Before use, the package must be carefully removed without touching the photo brag. It is important to do this carefully, since even from consumables for laser devices can wake up the coloring composition.

Pull the protective tape, as shown in the pictograms of the package. Cut the module in the horizontal position slightly so that the toner is distributed inside the container.

Replacing the cartridge in the printer: how to insert a new

Preparing the cartridge to install

Third Stage: Installing the cartridge

To properly install, it is necessary that all the protruding elements are easily entered into the grooves inside the printer. It does not need to apply great effort, the consumor should easily be placed inside the device.

If the replacement of the cartridge is incorrect, it started moving at an angle, no need to immerse it with strength, just remove it and start over. Next, close the lid, turn on the printer and wait until the equipment is ready for use.

Replacing the cartridge in the printer: how to insert a new

Installing a new cartridge

Printing a test page

Printing trial pages is required to assess the performance of the established consummer and its quality. Defects (for example, white stripes or black spots) are immediately noticeable on the sheet. This will determine the malfunction and replace the element to suitable until the start of immediate use (for example, to print photos or documents).

Follow these steps:

  1. Connect the equipment to the PC (the ability to print a test page using the buttons on the case is not available to all models).
  2. Click "Start" on the desktop of the computer and go to the "Toolbar" panel, and then in "Devices and Printers". The section name may differ for different version versions.
  3. Select the desired printer model and press it right mouse button.
  4. Open the "Properties" and then - the General tab.
  5. Click the "Test Print" button. If the printer is on and inside there is a paper, the test page will start.
  6. Wait until the sheet is printed (sometimes you need more time than when printing ordinary sheets).

Different printers have a format and list of items that are displayed on the test page. This is usually text with different fonts and graphics. In color models of printers, different colors are used to estimate the clarity of the display of each shade.

Printing should be high quality: clear lines without divorce and irregularities. Small defects can be corrected by programmatically. To do this, on the "Maintenance" tab, there are buttons for cleaning, checking nozzles, head alignment.

Replacing the cartridge in the printer: how to insert a new

Example test page

If these methods do not help, you can rinse the head or cartridge inkjet printer. This work is better to entrust specialists. In consumables for laser devices, it may be necessary to install a new photocell, drum or other components.

Some printers can create test pages using the housing buttons, which makes the procedure more comfortable.

Specificity Reset for various types of devices

The printer can be laser or inkjet. From this, the subtleties of the installation and the features of cartridges depend (they differ in size and configuration). In the first version, the sheets absorb the composition, in the second page "baked".

Technically, the cartridge replacement procedure in the laser and inkjet printer is approximately the same. Everything needs to be done carefully so as not to damage the element and equipment.

Laser printer

In laser equipment, the coloring powder is used, which may wake up, so it is advisable to perform the procedure in gloves, and the old cartridge is immediately disposed of.

Some models (for example, Samsung technique), when installing new consumables, it is required to reset the toner counter or the photo-brag resource.

Jet printer

For devices, liquid paints are used, so when removing the old element, it is necessary to prepare a trash can or store the desk with paper so that the surfaces are not blocked.

Replacing the cartridge in the printer: how to insert a new

Cartridges in an inkjet printer

For inkjet units, it is possible to replace only individual tanks with paint, and not the entire cartridge.

Some bike consumables are disposable, their refueling is not possible.

Replacing toner

If the cartridge is expensive, you can not change it, you only need to periodically refuel it with toner. It is more difficult to perform this procedure for a laser printer, which is due to the structural features of the equipment.

It is necessary to extract the node and disassemble a bit (unscrew the screws for the removal of the shafts and the photobaban). The removed items are cleaned from the remains of the old toner, then a new powder is placed in the container (pre-cleaning it from the old substance). Work is best done in the respirator or protective mask.

For an inkjet printer, you do not need to disassemble the cartridge to change the toner. If you need to pour black paint, there is a small hole in the cassette, through which the color composition is poured.

Replacing the cartridge in the printer: how to insert a new

Replacing toner

If the printer uses paints of different shades, then the toner is poured into each block. If there is no appropriate shade, the printer will still work, simply distorting color reproduction.

Possible problems

If the technique does not print after replacing the cartridge, contact the service center. You can try to independently reinstall another cartridge, but the fact that it will solve the problem is unlikely. However, the cause of the failure can be in the printing device.

You can not disassemble the cartridge housing, as it can damage the toner containers and disrupt the geometric parameters of the product (it will simply stop inserted).

Understand how to insert the cartridge is easy, the procedure is intuitive. However, sometimes it is worth asking for this person who has already performed this work.

Ended paint

Nowadays, printers are used to print documents and files. These are special peripheral devices connected to a computer and converting information from an electronic format in the database on a paper medium. The process of working any printer consists in a sequential execution of a specific cycle. It consists of several main stages:

  • Connecting equipment to a power source and a computer program recognition.
  • Configuring the print format and the quality of the displayed display.
  • Download cartridge and paper, start work.
  • Sequential printing of document pages.

This happens each time using the program. As can be seen from the planned manipulation plan, one of the main elements to work is the cartridge. For normal printing, it is necessary to monitor its condition, the amount of ink ... after full spending it is necessary to fill it or completely replace it with a new element.

How to remove the cartridge?

Before you start installing a new element inside the printer's housing, you must remove the old cartridge. Make it is simple enough, especially if there is experience with technology. However, if you perform manipulation for the first time, it is better to use step-by-step instructions and carefully remove the cartridge from the printer housing. For this, follow the instructions:

  1. Prepare a workplace, remove extra decorations and sunk sleeves for convenience and prevent paint.
  2. Gently lift the printer cover, look inside the case. During operation, some details can be very hot, be careful when you touch the elements.
  3. Find the cartridge, in some models it can stay at the expense of special clamps. Gently delay them without sharp movements, so as not to break.
  4. After release from the clamps, pull the special handles or recesses on the cartridge. If it is stuck, you should contact the service center for help. Sharp and strong movements can damage the technique.

When opening the cartridge enclosure, it can continue to continue moving without applying ink, do not stop them alone. Wait some time until the movement stops, then remove them.

IMPORTANT: Different versions of technology have their own characteristics when installing removable parts, it is worth reading the instructions and watch the training video.

It is necessary to get a cartridge very carefully because it contains a lot of small parts, the damage of which can adversely affect the print quality.

How not to bother in paint?

how to deliver

An important point when replacing the cartridge is the presence of the remaining paint. The problem is that the coloring composition, located inside the element, can be stained by human skin and surrounding items. In order to protect yourself and home interior elements, take advantage of the following tips:

  • Prepare the workplace, put the sheets of paper to the surface. Remove excess objects from the table.
  • Put on the old apron or cover the body with a towel. You must use the gloves in the hands, you can use old knitted knitted, which you have not used for a long time.
  • Also be robbed with rags or napkins to quickly remove the paint on the skin or clothing. Pass the solvent for paint removal when drying it.

IMPORTANT: Do not shake and do not turn the cartridge to check the level of the remaining ink, as it can lead to paint leakage.

Of course, various types of paint or polymer powder (toner) have different effects and require special precautions. In some cases, it will be useful to use personal protective equipment: rubber gloves, respirators, safety glasses.

How to fix the cartridge?

After you removed the old element, you can replace it with a new one, but to save money you can use refueling at home. It is easy enough to fulfill it even for a beginner, but at the first attempt some questions may arise. A step-by-step plan for performing manipulation will help to answer them:

  1. Prepare paint and syringe to introduce it inside the cartridge housing.
  2. Using the piston, fill the capacitance of the syringe to the top mark. You should not fill up to the limit, otherwise the paint can pour out.
  3. After that, find the hole on the outer package and enter the needle from the syringe into it. Start carefully and smoothly overflow the ink into the container, filling it.
  4. In the final stage, swipe all available holes in the cartridge to prevent ink loss.

Replacing the cartridge in the inkjet printer

In the case of toner for a laser printer, the process will be slightly different:

  1. Prepare personal protective equipment, since the polymer powder has high toxicity.
  2. Remove the element from the printer housing, inspect its walls. On the top cover should be a hole. With its absence, burn a small hole in the wall.
  3. After that, with the help of a special funnel, fall asleep powder into a free chamber.
  4. Then close the hole with a plug or adhesive tape.
  5. In some cases, the cartridge must apply a special chip (goes in the kit) so that the computer and printer's program recognize it

This option is suitable when using universal techniques and a suitable coloring material for refueling. Some manufacturers restrict the ability to work with non-non-elements, it is worth considering this before trying to insert a refilled cartridge. Information can be found on the cartridge housing or in the instruction manual for the printer.

IMPORTANT: You can not leave the printer for a long time without a cartridge, it can cause a failure to work and deteriorate print quality.

Therefore, it is recommended to quickly replace or refuel paint to restore the equipment in a short time.

How to insert the cartridge correctly?

After completing the refueling, the easiest action remains, now it is necessary to insert everything to your previous places. To perform it, do the following:

  1. Disconnect the needle and syringe, thoroughly rinse them until the coloring composition is completely removed.
  2. Put the cartridges on the smooth surface of the holes up in order for the paint inside of them.
  3. Now define the former place on a moving carriage. Disconnect the printer so that the printheads do not move and do not interfere with the main process.
  4. Pre-open the holes, removing the closing of their tapes or tape to get paint into the nozzle.
  5. Without sharp movements, insert the element into the device until the characteristic click signaling is indicated by the installation correctness. Do not put pressure with force.
  6. If you have clamps for fixing, move them slightly to accurately install all components.

Printing a test sheet

So you will definitely refuel the cartridge or establish new equipment if necessary. This will significantly save your money and time.

To improve work and enhance performance, read additional information about your equipment and use the tips:

  • Diagnose and troubleshoot problems.
  • Periodically, clean the elements of the design from dust, dirt and extraneous elements.
  • When refilling cartridges do not mix different compositions, it spoils printing machines.
  • If the equipment does not support other people's details, try not to apply them.

Subscribe to our social networks

How to remove the cartridge

How to pull out the cartridge from the printers of various models

If the printer stopped in the middle of printing and the toner indicator flashes on its panel, it is necessary to change the cartridge. Many do not know how to do it to pull the cartridge from the printer. The procedure is not complicated, you need to correctly perform several actions.

What will we talk about:

Types of printers and cartridges

The most common types of printers that are installed in offices and houses are:

  • Inkjet printers color printing;
  • Laser black and white print;
  • Color print laser printers.

Many manufacturers are combined in laser devices printing, copying and scanning. The cartridge in the modern printer is an independent unit that is easily removed and inserted into the device.

In it, under one case collected:

  • toner (coloring powder) for printing;
  • parts of the cartridge providing directly printing;
  • Chip transmitting information from a computer printer

The cartridge from the inkjet printer is a container, often from transparent plastic, a hermetically closed, having a chip for communication with a computer and equipped with a print head. In some printer models, each color cartridge are taken separately, there are models in which the cartridges of different colors are connected to one block with one head. In such cartridges it is easy to control the amount of ink and the need to replace it.

General Cartridge Recess Rules

Remove the cartridge from the printer if:

  • The indicator of the absence of toner or ink flashes;
  • Line on printing too pale;
  • A white strip is formed on the printed sheet;
  • In the printer stuck or broke the sheet.

You can select some general rules according to which the cartridge is removed from the device of any type.

First you need to carefully inspect the printer and determine its manufacturer and type. Typically, the printer brand is prescribed on the front working panel. The type of printer can be installed by looking at the printed sheet. If the front panel is not possible to read the name, on the back of the printer there is always a label with the full name of the manufacturer, the model, the serial number of the device. The same information is displayed on request in the computer's launch menu and printers.

Requests in search engines information on the model and the question: "How to pull the cartridge from the printer?" We will receive links with video, clearly showing the replacement process.

In order to pull the cartridge from the printer, you do not need to make strength. If everything is done correctly, the cartridge easily slides in the guide grooves.

Then check whether the printer is enabled. Inkjet models of printers allow you to pull out the cartridge only in the on state, you may not be in the laser of this need.

It is necessary to find the lid closing access to the cartridge. On its inner side, all manufacturers place a picture - instructions for replacing the cartridge that you can use to pull the cartridge.

Many printer models are equipped with a working panel where commands will be displayed, prompting the procedure for replacing the cartridge.

In some models of devices that combine a printer, a scanner and a copying device, a cover that closes access to the cartridge is under the scanning part.

In jet printers, after its removal, the printhead is automatically set opposite the access cover. After its stop, you can get a cartridge.

It is necessary to check whether there are fixing levers that hold it in place. If they are, then to pull out the block, you need to lower the levers and disconnect the cartridge.

In some cases, it is pulled out by movement strictly up.

A trying laser cartridge need to be attentive - with poor refueling, you can hardly stain a toner.

Remove the nr printer cartridge

In use there is a large number of modifications of HP printers. Consider the cartridge extraction procedure on the example of the LaserJet M1132 MFP LaserJet M1132 MFP LASERJET M1132 Printer and the Deskjet Inkjet Printer.

In order to pull the cartridge from the print multifunction printer NR LaserJet M1132 MFP photo:

  • Carefully learn the top scanner LaserJet NR Block, it will be fixed using special levers;
  • In some models there is a lid, additionally closing access to the cartridge, it must be lifted;
  • Caution, effortlessly pull over the black plastic knob of the cartridge, it should easily move on guide grooves;
  • The inscription in the absence of a cartridge appears on the control panel screen.

Removing the Cartridge from the printer HP

To remove the cartridge from the NR DESKJET printer:

  • turn on the printer;
  • Find and open on the front panel of the printer access to the cartridge;
  • wait until the print head locks;
  • Gently by clicking on the cartridge, pull it out of the nest.

Removing the Cartridge from the printer HP

How to pull the cartridge from the samsung printer

In order to pull the cartridge from the Samsung printer, you must:

  • turn on the printer;
  • Carefully leake the front cover - it is placed under the print tray and has a special emphasis for opening;
  • Carefully pull the cartridge to the open handle - to facilitate sliding in the grooves it is necessary to slightly lift.

How to Delete CANON Printer Cartridge

The Canon printer is inkjet type and black and white and colored laser printing.

In order to pull the CANON printer cartridge:

  • If the tray for loading the paper at the bottom of the printer, then raise the top cover of printing;
  • We fold a protective cover of the device, there is a special excavation for convenience;
  • pull the cartridge for the housing handle;
  • If the paper is loaded from above in the printer, then the lid folds down.
  • With proper pulling out the cartridge for action, no effort is required.

To replace the inkjet cartridges in the Canon Pixma Printer 2 of this manufacturer:

  • Enable the printer and wait for the download;
  • wait for the installation of the carriage;
  • de-energize the printer, stretching the cord from the outlet;
  • If the cartridges have a locking lever or cover, you need to raise it, lower the levers;
  • L By clicking on the cartridge, pull it out of the nest movement on yourself.

How to extract the cartridge from the Epson printer

To pull the Epson printer cartridge:

  • Check if the printer is enabled;
  • After starting and loading the printer, they cover the printer cover;
  • After stopping the printer's head, remove the cartridge movement towards myself;
  • If the cartridge is not removed, check if the lock lever in the printer and change its position in the printer;
  • In some models, the cartridge will remove after easy pressure on it to the sound of clicking.

In some Epson models, after opening the cover covering the cartridge, for 3 sec. Press the ink control button. After that, remove the cartridge by the direction of strictly up, squeezing the edge to release latches-locks.

Replacing the CANON PIXMA MG2540 printer cartridge

Replacement

If ink ink ends during the printing process or other errors appear, the ink indicators and alarm (Alarm) begin to flash orange, informing about the error. Consider the number of indicator flashing and perform the necessary actions. If an error occurred

Replacement procedure

For replacement, follow these steps.

Do not touch electrical contacts (a) and print head nozzles (B). When touching them, the device can print incorrectly.

After extracting, it should be replaced immediately. Do not leave the device without it (sell cartridges to the printer, buying, buying expensive, buying cartridges for printers, sell expensive, pass, buy - buying more expensive, buying cartridges to printers, buying with overdue dates, redemption with expired dates, buying expensive, buy wholesale a lot, sell new cartridges from printers).

Use a new to replace. The installation of used in use can cause clogging of the nozzles.

In addition, the device will not be able to provide the right information if replaced.

After installation, do not remove it from the device and do not re-install in the operation of the device there is a problem. To achieve maximum print quality, the resource needs to be spent within six months after the first use.

If ink ends, you can continue to print for some time only with the help of black or color, in which the ink remains. However, the print quality will be lower compared to printing with two. To obtain optimal characteristics, it is recommended to use new ones. Even when printing in one type of ink is not removed empty. No color or black causes an error and stopping printing in the device.

Colored ink can be consumed even when printing a black and white document or when choosing black and white printing.

Both colored, and black inks are also spent with standard and deep cleaning head, the execution of which can be necessary to ensure the operation of the device. If it ended in ink, replace the new one.

1. Make sure that the power is turned on.

2. Fold the paper reception tray and an additional paper reception tray.

3. Open the lid.

The holder moves to the replacement position.

Do not attempt to stop or move the holder manually. Do not touch the holder before it stops.

Internal parts of the device can be fan in ink. When replacing, make sure that you do not drink hands or clothing. Ink is easy to remove from the inner parts of the device with paper napkins, etc. Do not touch the metal or other internal parts of the device.

If the lid remains open longer than 10 minutes, the holder can move. The alarm indicator lights up (Alarm). In this case, close the lid, and then open it again.

4. Remove empty. (1) Press it until it stops (it should be rolled up).

Observe caution when performing operations so as not to stain clothes or surrounding space.

Dispose of empty in accordance with local laws and regulations on the utilization of consumables.

5. Prepare a new one.

(1) Remove the new packaging and carefully remove the protective tape (C).

When shaking ink can shed and blur your hands and surrounding space. Contact carefully.

Caution: Ink on remote protective tape can be stained your hands and surrounding space.

Do not attach a protective tape back after removal. Dispose of it in accordance with local laws and regulations for the disposal of consumer goods.

Do not touch the electrical contacts or printhead slots. When touching them, the device can print incorrectly.

6. Install it.

(1) Insert the new angle in the holder.

Color one should be installed in the left nest, and black - right.

Carefully install it so that it does not hide electrical contacts on the holder.

(2) Press it with an effort before fixing.

Check if it is installed correctly.

The device will not print until color and black will be installed. Be sure to install both.

7. Close the lid.

If the Alarm indicator (ALARM) is lit or flashes after closing the cover, follow the appropriate action.

If an error occurred

During operation, the device may issue noise.

8. Adjusting the position of the printheads.

During the alignment, the device automatically clears the print head to print a print head alignment sample. Do not perform other operations before cleaning the print head of the device.

How to pull the cartridge from the printer

Many of us in the office or at home there is an extremely useful and even indispensable device - printer. With the help of it, you can print a large number of documentation you need to study, work or just for your beloved business. However, sooner or later the moment occurs when you need to understand how to pull the cartridge from the printer. Such a need appears due to the following reasons:

  • The dyeing substance (ink, powder) ended;
  • There is a bad or pale text printing;
  • stuck a sheet of paper that stopped the operation of the device;
  • On the printed paper, bands, divorces, blots are observed;
  • An error caught fire on the computer monitor or the printer's display.

Description of the procedure

Remove the cartridge from the printer - the case is simple. Difficulties may occur only for the first time. Then you will do it with closed eyes.

First, find the instruction. Often it is clearly painted on how to properly remove the cartridge. Many manufacturers in the instructions apply schemes or even pictures, extremely facilitating the "life" of the user. Cribs are found on the device itself itself: rear, side or under the top lid.

For most printer models, this procedure is similar, since the location and fixation of cartridges is almost the same. Therefore, we give a general description of how to quickly remove this element from the printing device.

Video, how to pull the cartridge from the printer Samsung ML-2015

We start with the fact that we turn on the device to the network. The current will not hit you, and the power is necessary due to the fact that many devices when turned off the cartridge is securely fixed inside the device and it is impossible to pull it out.

We are waiting for a few minutes: the device will simplify and will be ready for work. Then open the top cover - for this you do not need any special tool, everything is done with even one hand. Usually on the side or under the lid there is a special platform or a notch for which you can pull.

After this, the block with the cartridge moves to the middle, the so-called service window. Here it is just easily removed. It remains only to understand the system of fasteners. Most models the cartridge is removed as follows: slightly press on the front part, lower the element down and pull it out of the grooves. In some printers, the cartridge is recorded at the expense of special clamps. Click on the buttons or small protrusions (levers) on the sides and pull on yourself.

If something does not work, then do not be nervous and do not apply force. The result will be one - the output of the device. Carefully read the instructions, try finding information on the forums or ask the question about your printer and how to safely remove the cartridge.

You did everything and you noticed that the inner parts of the printer were fan in ink? Take a dry napkin or a piece of unnecessary clean fabric and carefully remove the contamination.

Precautions

  • To protect yourself from getting injuries, remove rings, bracelets, hours, etc. It will also help to avoid possible damage to these items.
  • All steps to select the cartridge from the printer should be carried out with minimal effort. If something does not disconnect, then first think about whether everything is done correctly. Contact instructions well in such cases.
  • The cartridge is not recommended to leave in the light. Especially under the influence of direct sunlight. It badly affects his future work.
  • When removing, be careful and careful not to make hands and clothes
  • It is best to immediately put a new cartridge. Otherwise, the printing elements of the device can dry, and significantly affect the print quality, which will require access to the service center.
  • More efficiency in the seizure of the cartridge due to its design requires inkjet models. If you leave the device without coloring item, that is, the risk of drying ink.
  • Laser printers have a strong thermofixer. Therefore, be careful - it is easy to burn.
  • Before starting the procedure, it is best to remove the paper feed compartment so as not to make clean sheets.

Below are video on how to pull out the cartridge from the HP Deskjet 2050 and Canon LBP 2900 printers.

How to independently replace the cartridge in the printer?

Sooner or later, the owners of printers have to face with the solution of such a task as the replacement of the cartridge. But it should be immediately noted that the replacement of the cartridge in the printer is not such a difficult and difficult problem, as it may seem like most. In addition, in the instructions attached to each model of office equipment, whether it is a printer or MFP sets out enough detailed information on how to replace the cartridge in the printer. Please note that if you act completely relying on your intuition in this case, this can lead to errors that will certainly have a negative way to play your printer.

First stage: Remove the old cartridge

Before pulling out the cartridge from the printer, you should enable the device and open it to the cover to access the consumables inside it. It is easiest to deal with cartridges that equip laser printers, because They are one whole box having a grasp handle.

So, to answer the question of how to pull the cartridge from the printer, you should pull it for the handle. The direction will depend on the rails located on the sides of the printer case. It should be removed neatly without any additional effort. Otherwise, if you remove it not in the direction, you can break not only this consumable item, but also the device itself. In addition, it's no secret that plastic is quite fragile.

In this case, the question arises how to extract the cartridge? To get the consumility as accurately as possible, keep it exclusively for the handle and, if necessary, for ends. Consequently, touch the photorad or moving parts of the cartridge is impossible! In addition, it should be noted that from such a consumor can wake up the residues of toner, which is a very corned and toxic substance. If you are swapped, then wash off the toner residues from the skin with cold water and any suitable cleaning agent. It is better to remove clothing at the same time and remove on washing. Thus, now you have learned about how to remove the cartridge from the printer.

Second Stage: Preparation of a new cartridge

At this stage you will need to install a new detail on the place of the old consumor. But before inserting the cartridge to the printer, make sure that it is really suitable for your device. For example, if you have a HP printer, then you can replace the expenditure item in it on the same model or unoriginal, which is compatible with the model of your printer. In general, today the market offers a large range of cheap compatible cartridges and the choice between the original and the compatibility is exceptionally for you.

To solve the task associated with how to insert a cartridge in the printer first print a new consumable material. Inside the box with a cartridge you will see shockproof hermetic packaging. You will need to operate and remove it from the cartridge, after which it carefully remove it without touching the contacts and the photo brag. Try to take care of cleanliness in advance, because Even of the new cartridges intended for laser printers can wake up toner. Next, remove the packaging tape and the safety tape, which is on contacts. Turn the new cartridge forward and backward several times, while holding it in the horizontal position. This will give the opportunity to host the tank at the tank most uniform it easily.

Third Stage: Installing the cartridge

Next, proceed to solving the task of how to install the cartridge correctly and competently. To do this, you only need to insert it, hitting the protrusions to the appropriate grooves. Essential efforts do not apply, because The consuming must be installed quite easily. After that, insert it into the body of the device until the stop. If something initially went wrong, be sure to remove this part and try again. Try to avoid distortions, otherwise the replaced cartridge will not get completely on your place. After that, you can close the printer cover and wait until the device goes into the working condition. Thus, the question of how to put the cartridge in the printer is solved quite simple.

Do not forget to print trial pages at the end to make sure that the cartridge has fully approached your printer and works in normal mode. If the cartridge is not installed properly, you will have to open the lid again and remove the consumility.

In addition to the above, it should be added that in the technical plan to replace the cartridge in the printer intended for the inkjet model, it looks almost the same as in the case of a consumable for a laser device. But before removing the cartridge in the printer of this type, pay attention to the presence of tanks. The fact is that to solve the question of how to change the cartridge in the jet model printer can be somewhat simpler, because They allow you to replace only separate tanks with ink as they are consumed. In general, as you probably made sure, setting the cartridge to the printer is a fairly simple process requiring sequence and accuracy.

How to get, insert printer cartridge

How to get the cartridge from the printer or how to install it correctly? Answers to these question is looking for every owner of copying and printed office equipment. Some find them in the instructions for the apparatus, others are trying to figure out intuitively, the third turns for help to Google. Attempts to extract or insert the cartridge independently lead to negative consequences - breakdowns of fixtures and fixing latches. In this case, the printer is diagnosed and repair. To avoid unforeseen breakdowns, we recommend reading the instructions, how to insert a cartridge or remove it from the printer.

When does the need to replace the cartridge?

  • after transportation of office equipment;
  • toner ends and need a cartridge refill;
  • The laser printer flashed paper and needs to extract sheet scraps;
  • Print defects appeared, the cause of which is the wear of the cartridge parts;
  • For diagnostics, for example, when the printer does not print.

Attention! Do not forget to recover the cartridge and replace the photo drum. This detail plays a significant role in the process of printing and affects its quality. You can use the services of our masters who quickly replace the photoreceptor and refueling the cartridge on the road.

How to pull the cartridge from the printer - the main recommendations

  1. 1 Do not make big effort. Consumables should be easily installed and removed from the print path.
  2. 2 Look into the instructions or locate the user manual on the Internet. To do this, you need to know the model of the printer or cartridge.
  3. 3 In the jet printer, the extraction is carried out after its inclusion. In many models, get consumables without tension will not work.
  4. 4 Do not follow the printer parts with a "careful" mark (exclamation mark). Before removing the cartridge from the printer with laser printing technology, we recommend that you make time to cool the thermoweean (stove).
  5. 5 If the toner is running out of the cartridge, then you can swap. Be careful, in no case do not wash off the toner with hot water clothes. Only cold. Use soap, powder or other detergent.

How to get a CANON laser printer cartridge

  1. 1 Disconnect the printer from the network.
  2. 2 In the MFP, it is necessary to raise up a block with a scanner.
  3. 3 Open the print edema cover.
  4. 4 Cartridge is equipped with a handle, you will not confuse it with anything.
  5. 5 Pull the consumage on yourself.

This scheme is suitable for most models. Now you know how to pull the cartridge from the Canon printer.

How to get a cartridge from the HP LaserJet printer

The LaserJet series is the most popular and oldest line of laser printers. You can get the consumable in 2 movements.

  1. 1 Start the device. Open the cover by pressing the mechanical button on the housing or pulling the handle.
  2. 2 Inside the print path, you will see the cartridge. Pull it until complete extraction in the free side.

Note! In LJ Pro M102A / M102W / M130A / M130FW / M130A / M130FW / M130NW printers, the CF217A cartridge is used, the refueling of which is carried out in our service center. It is blocked by two paws in the off state. They can be moved manually or just run the machine - the system will automatically unlock them. In the LaserJet Pro CP1025 and CP1025NW and CP1025NW printers, after switching on, click on the control panel to the cartridge you want to get.

How to insert the cartridge to the printer - TONFIX masters tips

  1. 1 On the cartridges after transportation there are protective tapes, corks or covers. They protect the consumption of waking up and damage to the photobaban. As a rule, they are orange. Before installing, they must be removed.
  2. 2 Make sure the cartridge is compatible with your printer. There are consumables that are very similar to yours, but have small structural cancellations: a small protrusion, another location of the clamps, the side cover has a different form, etc. You think how to insert a cartridge in the printer, and it just does not fit.
  3. 3 Signal that the cartridge is installed correctly, there will be a click.
  4. 4 After refueling, do not forget to replace the chip on Samsung, Xerox, Dell, Kyocera printers and new models from HP. Even if the consuming is installed correctly, the printer does not recognize the cartridge.
  5. 5 Shake the cartridge left-right 5-6 times so that the toner is uniformly inside the bunker.

Note! SAMSUNG, HP, Xerox and Dell laser printer firmware will save on service equipment. Order this service in our service center, save along with Tonfix.

How to insert cartridge to the canon printer

  1. 1 Open the lid. If you are a user of MFP, then you first need to raise the scanner block.
  2. 2 Put the cartridge on the sled - guides in the printing compartment.
  3. 3 Enter the consumility, holding it for the handle.
  4. 4 When the cartridge is stored in the landing socket, slightly push it on it.
  5. 5 You must hear a characteristic click. Now, you know how to install the cartridge in the Canon printer. Agree, it is not difficult.

How to insert a cartridge in the hp printer

  1. 1 Remove all protective films and ribbons from the cartridge.
  2. 2 In MFP, it is necessary to raise the scanner up.
  3. 3 Open the printer cover.
  4. 4 Put a consumers to guides.
  5. 5 Insert until it stops. You must hear a characteristic click.

Note! How to insert the cartridge to the HP printer with color cartridges. In the sleds for each cartridge there is its own position. Do not confuse colors, the colors sequence does not matter. In the LaserJet Pro CP1025 and CP1025NW, before installing the cartridge, click on the corresponding button on the control panel (the key color coincides with the color of the cartridge). Do not forget to print the test page to check the print quality.

Features of other printer brands

  1. 1 Brother. . In the printers of this brand, a separate system is used: drum units and a toner unit. How to remove the cartridge from the Brother printer: get drum unit and disconnect the toner cartridge by clicking on the blue paw. Clean the corona wire inside the photo brag, slide the slider on the right left. Observe the reverse sequence during the reverse order.
  2. 2 Kyocera. . You can extract the entire block by pulling it by the handle or get only a toner cartridge. To remove a toner tube, you need to push the blue handle located on the left, and pull the container on yourself. During the reverse installation, it is recommended that you press the handle to the "Releas" position (open). Only after that a new consumator is installed and snaps into the "Lock" position.
  3. 3 Xerox. . How to remove the Cartridge from the Xerox Phaser 3100mfp / s printer? For this you need a smart card. In the remaining models, the principle of extraction is no different. You need to turn the cartridge or push the latch.

If you need an operational refilling of cartridges, the prevention of a laser printer or its full service, you can rely on the Masters of the Tonfix service center. When repairing office equipment, the departure of the master and diagnostics are not paid. We give a guarantee for all types of services.

Instructions, how to get a cartridge from the printer Epson, Samsung, Canon and any other

If you do not know how to pull the cartridge from the printer, then this article is for such situations. Note that for the laser device you need to remove the "consuming", and with the jet to remove. This difference is really important, it should be considered not to damage the device itself. This instruction will show actions for the extraction for the technique of any well-known manufacturer. The recommendations were successfully tested on such models: HP LaserJet (M1132 MFP and P1102), Samsung (SCX 3400, 3200), Canon (PIXMA MG3640, MF3010, MG2440), Pantum M6500, Xerox WorkCentre 3045.

Causes of extract

  • When the coloring agent in the cartridge becomes little, but there is still enough for print for some time, you will see a warning. When toner or ink will end, it will be displayed on the quality of printouts. And some models can start issuing even errors and block the operation of the device.
  • It happens that the printer itself begins to flure and refuses to print. One option to resume work can be the procedure for removing and installing the cartridge. Less often it helps with problems with chip. But, most likely, the latter will have to be replaced with a new or reset.

General recommendations

Precautions

When you take the cartridge even to refuel, then in it still remains a slight dye residue. In this case, the printer can use badly - this is normal. The dyes used consist of different chemical elements that are not always or disturbed from the skin, clothes or surface of furniture, walls, carpets. Simply put, you can be decently stain. That this does not happen to prepare the workplace accordingly. At home you can:

    "Clear" the table from all unnecessary and stack that film or paper, or newspapers.

Features of devices of different types of print

Print devices are of different sizes, types, formats and other characteristics, but the most important is the method of printing it. It can be: laser or inkjet. There are other, but less popular. Consider the main nuances that occur if necessary to get a cartridge from the printer of each of the print formats.

How to remove the laser

  • A collection cartridge is used in the laser printer, which consists of a toner tube and a photograph.
  • There are collapsible or drum cartridges, where the parts mentioned are separate elements. They are less common.
  • In 90% of cases, only one "consumator" with a black dye is used.
  • If we follow the precautionary measures, it is recommended to pull out the laser cartridge only after turning off the printer from the network.
  • If before this device continuously worked continuously, it is better to give it a little cool in the literal sense of the word.
  • Stretching is behind a small handle, which is located in the center of the cartridge. Try always towards "on yourself".

How to remove with inkjet

  • 4 cartridges are used in the inkjet printer. One black, blue, yellow and red. Models with only black is practically no on sale for a long time. But more appears with more than three color inks, namely six and eight.
  • It is necessary to pull out each separately in turn.
  • Many models require power and pressing a specific combination of buttons to exit the tray with "banks" to the removal position. But it happens that it is enough just to open the lid.
  • Be sure to ask the presence of instructions for changing cartridges in the documentation for your model.
  • To withdraw from the carriage, it may be necessary to click the protective cover.

Features of different brands

Canon

If you have a PIXMA series color apparatus, then:

  1. Turn on the device and wait until it finishes to work.
  2. Open the lid and check that it is securely sam.
  3. The cartridge carriage will start "ride", and then it will become in one place.
  4. Lead techniques, and then proceed to remove cartridges.
  5. It can hold the clamp or "tongue" that should be carefully pushed off.

The devices of the "G" series are equipped with a continuous ink supply system, and therefore the cartridge replacement is not required. It is enough to add paints to continue the seal.

The line of technology with the LBP logo is modern laser devices. Pull out the cartridge from such a printer is very simple. Perform such simple steps:

  1. Turn off the power to the button or pull out the power cord.
  2. Open the front cover.
  3. Do not notice the cartridge inside will be difficult.
  4. Take a tube for the handle in the center and pull on yourself.
  5. All is ready!

For laser action similar to any brand of printer:

  1. Disable power required.
  2. If you own the MFP, it will be necessary to raise not one, but at once two covers.
  3. The cartridge itself pulls up.

"Bunkers" of this company are sold under the DESKJET or OFFICEJET label. Their cartridges in form and maintenance are almost identical to Canon Pixma. To get, do this:

  1. Enable your printing device.
  2. You can immediately raise the lid.
  3. Wait for the carriage stop.
  4. Inkwells in it can be fixed with latches.
  5. Help should be moved up.

Brother.

Pretty popular and reliable devices that were sold a lot. And therefore there is interest in the plan for replacing consumables. For what and you need to pull the tube with a toner. For this:

  1. De-in technology and only then continue any actions.
  2. Find the lid behind which the cartridge is located.
  3. First lift the part on which the control panel is located on the housing.
  4. If necessary, open the second damper.

The jet technique of this manufacturer is marked with a "MFC" label. Such printers cartridges are on the right on the case. Prevent extraction can holder.

Epson.

  • The printer must be in a working condition. Otherwise we turn it on.
  • As soon as it completes the procedure for preparing for printing, open the lid.
  • The print head may not stand still, but something to do. We wait until not to stop.
  • We check if there are no clamps that may interfere.
  • Give the cartridge pulling on yourself or by pressing it to a characteristic click.

Xerox.

Nothing difficult is waiting for you in the process of pulling out toner from the casing of the Xerox printing apparatus. Everything comes down to three steps:

  1. Turn off the printer.
  2. Open the lid.
  3. Pull the cartridge for yourself by the handle.

Kyocera.

Some models use a few unusual external signs of the cartridge. And its placement inside the device is also unusual. Consider on the example of the model Kyocera FS 1040. To get a tube need:

  1. Throw back the front tray cover.
  2. The side part of the cartridge will be visible to the left.
  3. Left hand hold the printer for the housing.
  4. Right, breaking down a bit left to the right or up-down, pull the "consumage" on yourself.

Pantum.

The most popular printer of this Chinese brand is M6500. In his example, you can see how the "consumable" is removed. And also in the video there is instructions for refueling.

Samsung

  • Remove the printed sheets from the output tray.
  • Open the cover up.
  • Fix at stops.
  • Take the cartridge for the handle in the middle.
  • Try to yourself up.

How to get the cartridge from the printer?

How to remove the cartridge from the printer?

Many users of printed devices are interested in how to remove the cartridge from the printer, because often in the process we are faced with a similar need.

Manufacturers advise less to interfere with the operation of the device, especially if we are talking about its internal components. But the question of how to remove the cartridge from the printer can be relevant in many situations:

  • - the text stopped printed;
  • - the device began to chew paper;
  • - The drum began to dump the material.

Therefore, we advise you to deal with this topical issue.

Cartridge removal procedure

You can pay for light by 30-50% less depending on what exactly the electrical devices do you use.

It is recommended to pre-remove all metal items from hand to not get damage. Correcting how to extract the cartridge from the HP printer, first open the lid carefully. It should be avoided contacts with a heated thermophilic. Then you should find a lever to weaken special locks.

The cartridge from the printer must be pulled out by pulling on itself. When building items, it is not recommended to take independent measures. This question needs to contact the service center.

Work with an inkjet printer

The question is how to remove the cartridge from the HP printer, you are interested in users when the device simply stops performing its function. Print defects may appear:

  • - White stripes,
  • - black divorces,
  • - Print gaps,
  • - Fuzzy letters and images.

In such situations it is recommended Remove the old cartridge To install a new one. If you use inkjet equipment, the replacement procedure may be pretty soon.

It is recommended that you make sure that you have disabled the equipment from the network. Then you need to open the tray used for paper. The device cover opens and fixes using the stop. To pull the cartridge without problems, wait until the device fully stops after opening the panel. Do not touch the printed head in the process. The user needs to open the locking box, which is placed in the cartridge, and pull out the part from the compartment. Be careful: the details of the device can be stained with ink. With the cartridge you need to handle carefully not to damage any part. It is recommended not to raise the drum curtain and not to leave the equipment under the right sunlight.

Below is the thematic video:

How to get the cartridge from the printer?

          How to remove the cartridge from the printer?

Many users of printed devices are interested in how to remove the cartridge from the printer, because often in the process we are faced with a similar need.

Manufacturers advise less to interfere with the operation of the device, especially if we are talking about its internal components. But the question of how to remove the cartridge from the printer can be relevant in many situations:

  • - the text stopped printed;
  • - the device began to chew paper;
  • - The drum began to dump the material.

Therefore, we advise you to deal with this topical issue.

Cartridge removal procedure

Use electrical appliances just as before, and pay 2 times less!

You can pay for light by 30-50% less depending on what exactly the electrical devices do you use.

Read more >>

It is recommended to pre-remove all metal items from hand to not get damage. Correcting how to extract the cartridge from the HP printer, first open the lid carefully. It should be avoided contacts with a heated thermophilic. Then you should find a lever to weaken special locks.

The cartridge from the printer must be pulled out by pulling on itself. When building items, it is not recommended to take independent measures. This question needs to contact the service center.

Work with an inkjet printer

The question is how to remove the cartridge from the HP printer, you are interested in users when the device simply stops performing its function. Print defects may appear:

  • - White stripes,
  • - black divorces,
  • - Print gaps,
  • - Fuzzy letters and images.

In such situations it is recommended Remove the old cartridge To install a new one. If you use inkjet equipment, the replacement procedure may be pretty soon.

It is recommended that you make sure that you have disabled the equipment from the network. Then you need to open the tray used for paper. The device cover opens and fixes using the stop. To pull the cartridge without problems, wait until the device fully stops after opening the panel. Do not touch the printed head in the process. The user needs to open the locking box, which is placed in the cartridge, and pull out the part from the compartment. Be careful: the details of the device can be stained with ink. With the cartridge you need to handle carefully not to damage any part. It is recommended not to raise the drum curtain and not to leave the equipment under the right sunlight.

Below is the thematic video:

How to pull out the cartridge from the printers of various models

If the printer stopped in the middle of printing and the toner indicator flashes on its panel, it is necessary to change the cartridge. Many do not know how to do it to pull the cartridge from the printer. The procedure is not complicated, you need to correctly perform several actions.

Types of printers and cartridges

The most common types of printers that are installed in offices and houses are:

  • Inkjet printers color printing;
  • Laser black and white print;
  • Color print laser printers.

Many manufacturers are combined in laser devices printing, copying and scanning. The cartridge in the modern printer is an independent unit that is easily removed and inserted into the device.

Cartridge

Cartridge

In it, under one case collected:

  • toner (coloring powder) for printing;
  • parts of the cartridge providing directly printing;
  • Chip transmitting information from a computer printer

The cartridge from the inkjet printer is a container, often from transparent plastic, a hermetically closed, having a chip for communication with a computer and equipped with a print head. In some printer models, each color cartridge are taken separately, there are models in which the cartridges of different colors are connected to one block with one head. In such cartridges it is easy to control the amount of ink and the need to replace it.

General Cartridge Recess Rules

Remove the cartridge from the printer if:

  • The indicator of the absence of toner or ink flashes;
  • Line on printing too pale;
  • A white strip is formed on the printed sheet;
  • In the printer stuck or broke the sheet.

You can select some general rules according to which the cartridge is removed from the device of any type.

First you need to carefully inspect the printer and determine its manufacturer and type. Typically, the printer brand is prescribed on the front working panel. The type of printer can be installed by looking at the printed sheet. If the front panel is not possible to read the name, on the back of the printer there is always a label with the full name of the manufacturer, the model, the serial number of the device. The same information is displayed on request in the computer's launch menu and printers.

Requests in search engines information on the model and the question: "How to pull the cartridge from the printer?" We will receive links with video, clearly showing the replacement process.

In order to pull the cartridge from the printer, you do not need to make strength. If everything is done correctly, the cartridge easily slides in the guide grooves.

Then check whether the printer is enabled. Inkjet models of printers allow you to pull out the cartridge only in the on state, you may not be in the laser of this need.

It is necessary to find the lid closing access to the cartridge. On its inner side, all manufacturers place a picture - instructions for replacing the cartridge that you can use to pull the cartridge.

Many printer models are equipped with a working panel where commands will be displayed, prompting the procedure for replacing the cartridge.

In some models of devices that combine a printer, a scanner and a copying device, a cover that closes access to the cartridge is under the scanning part.

In jet printers, after its removal, the printhead is automatically set opposite the access cover. After its stop, you can get a cartridge.

Removing the cartridge

Removing the cartridge

It is necessary to check whether there are fixing levers that hold it in place. If they are, then to pull out the block, you need to lower the levers and disconnect the cartridge.

In some cases, it is pulled out by movement strictly up.

A trying laser cartridge need to be attentive - with poor refueling, you can hardly stain a toner.

Remove the nr printer cartridge

In use there is a large number of modifications of HP printers. Consider the cartridge extraction procedure on the example of the LaserJet M1132 MFP LaserJet M1132 MFP LASERJET M1132 Printer and the Deskjet Inkjet Printer.

In order to pull the cartridge from the print multifunction printer NR LaserJet M1132 MFP photo:

  • Carefully learn the top scanner LaserJet NR Block, it will be fixed using special levers;
  • In some models there is a lid, additionally closing access to the cartridge, it must be lifted;
  • Caution, effortlessly pull over the black plastic knob of the cartridge, it should easily move on guide grooves;
  • The inscription in the absence of a cartridge appears on the control panel screen.
Removing the Cartridge from the printer HP

Removing the Cartridge from the printer HP

To remove the cartridge from the NR DESKJET printer:

  • turn on the printer;
  • Find and open on the front panel of the printer access to the cartridge;
  • wait until the print head locks;
  • Gently by clicking on the cartridge, pull it out of the nest.
Removing the Cartridge from the printer HP

Removing the Cartridge from the printer HP

How to pull the cartridge from the samsung printer

In order to pull the cartridge from the Samsung printer, you must:

  • turn on the printer;
  • Carefully leake the front cover - it is placed under the print tray and has a special emphasis for opening;
  • Carefully pull the cartridge to the open handle - to facilitate sliding in the grooves it is necessary to slightly lift.
SAMSUNG printer

SAMSUNG printer

How to Delete CANON Printer Cartridge

The Canon printer is inkjet type and black and white and colored laser printing.

In order to pull the CANON printer cartridge:

  • If the tray for loading the paper at the bottom of the printer, then raise the top cover of printing;
  • We fold a protective cover of the device, there is a special excavation for convenience;
  • pull the cartridge for the housing handle;
  • If the paper is loaded from above in the printer, then the lid folds down.
  • With proper pulling out the cartridge for action, no effort is required.

How to pull out the cartridge from the printers of various models

To replace the inkjet cartridges in the Canon Pixma Printer 2 of this manufacturer:

  • Enable the printer and wait for the download;
  • wait for the installation of the carriage;
  • de-energize the printer, stretching the cord from the outlet;
  • If the cartridges have a locking lever or cover, you need to raise it, lower the levers;
  • L By clicking on the cartridge, pull it out of the nest movement on yourself.

How to pull out the cartridge from the printers of various models

How to extract the cartridge from the Epson printer

To pull the Epson printer cartridge:

  • Check if the printer is enabled;
  • After starting and loading the printer, they cover the printer cover;
  • After stopping the printer's head, remove the cartridge movement towards myself;
  • If the cartridge is not removed, check if the lock lever in the printer and change its position in the printer;
  • In some models, the cartridge will remove after easy pressure on it to the sound of clicking.

In some Epson models, after opening the cover covering the cartridge, for 3 sec. Press the ink control button. After that, remove the cartridge by the direction of strictly up, squeezing the edge to release latches-locks.

Добавить комментарий