Pchelituer. The site of the amateur beekeeper. - How to make a working box with your own hands

Any beekeeping when working with bees, you must have a working box, which, if necessary, you can put a certain number of frames. Especially such a box is needed when pumping honey.

It is better to do the working box, because sometimes you want to sit down and relax, and there is nothing nearby in bars.

Collecting your working box, I proceeded from the fact that it should be not very heavy, since when carrying a honey frame mass and so large enough.

My working box is designed for 6 frames (470 * 300).

Box. Appearance

Box. Appearance.

Since the width of one frame is 37 mm, then the width of the box should be 37 * 6 = 222 mm, and it is better a little more to make it easier to put the framework, especially if they are reflected, i.e. 23-24 cm.

I made the side walls from the broad "twenty". I had one suitable board, but even if there is no such wide board, you can use ordinary boards, collecting them in a quarter, in a spike or swallow tail. This is someone as you like.

For the side walls, I used a thin paneur (4 mm), reinforced by the perimeter with thin wooden planks.

Calculate the size of the working box:

Height: 300 + 50 = 350 mm (height stock)

Width: 37 * 6 = 222, but it is better to 40 * 6 = 240 mm (my suitable board turned out to be 23 cm, which is also not bad).

Length of lateral parts: 470 + 2 * 20 (thickness of the board) = 510 mm. You can make a small stock of 5 mm. Those. The dimensions of plywood will be 510x350.

The dimensions of the planks that make up the ribs of stiffness around the perimeter of plywood are not critical.

Collective box is very simple. With the help of a screwdriver, twist 2-3 screws in height in the end of the side board.

1220359.

View of the working drawer from the inside.

The bottom and the cover are cut in size from 4-millimeter plywood. The dimensions are better to determine with the help of a roulette when the box will already be collected, because In advance it will be impossible to take into account the thickness of the planks (rigidity).

If the size length is 510 mm, then in thickness it will turn on: the thickness of the board, plywood and planks stuffed on the phaneer. It is necessary to take into account this, because it is to the planks (and side boards) a bottom will be attached - so the design will be tougher.

On the inside of the lid, it is necessary to fill the planks that will correspond to the internal perimeter of the working box.

 

So the lid will close tightly.

Why didn't I use the loop? Sometimes when working, it is necessary to open the cover on the loop, the additional space is needed, but by and large - this is a matter of habit. It is more convenient for me to work with such a lid.

For carrying a box, you must provide handles. I did one.

On the side boards, I nailed powerful brackets and handed it out through them.

 

The result was the following:

I just handed the ring and tied the knot. The knot tried to put closer to the bracket so that he would not interfere with when working.

1220357.Transfer of a working drawer in hand

Why did I use this method of carrying? Yes, very simple. Most often I use the working box for carrying frames. And everyone knows that the framework, especially with honey, is heavy. Judge for yourself. Rutta's full-fledged frame has a mass of 3-3.5 kg, the Dadan frame is 4-5 kg. And if these frames are at least four, the mass increases to 14-16 kg. In the hands of this weight, you can drag ... two times. And if a lot of frames?

The sling can also hang on the shoulder and distribute the load.

1220362.Transfer of a working drawer on the shoulder

 What else can I use the working box?

In addition to carrying the framework to the working box, I plant a swarm. It is understood that for ROOV specially invented Roya. But I like working with a working box more. I will explain why. A couple of times I used ROOV. Bees behaved restlessly. They had to be withstanding for a long time in a dark place, and once the swarm from me simply "escaped."

To catch the swarm, I take a working box and put 3-4 frames there, it is better that at least in one of them was honey.

And here with this "wealth" I climb on the tree where Roy was invented. Uncomfortable, I agree. And what verbal momentum I'm talking when I climb on a tree ... Every time I stubbornly proving myself that I am not right and is much easier with Roast. Apparently I regain.

Most often, I leave the working box on the nearest fork, pull out one of the frames and gently put it on the swarm and just waiting. In 90% of cases, the bees begin to actively transfer to the frame. You can substitute the frame from below and throw onto it the main mass of bees. The main thing that the uterus is on the framework. And then it all depends on how many bees it is necessary to guess that the uterus on the branch is no longer. Many times I had cases when I put the frame to the working box and all bees ranked in it. The branch remained either the most stubborn or the most closestly. It happened that I set the working box under the tree (when the uterus was already in the working box) and watched an amazing picture when Roy starred from the branch and climbed into the box.

It doesn't make sense to withstand in the box of bees for a long time. It is enough of that time that is necessary to prepare a new place for Roy and install the housing. Bees neatly on the framework are transplanted into a new home and in a few minutes begin to nourish.

For the convenience of the health profession from the hives, the beekeepers of all over the world use various patterns of carrying or, as they are also called, Ramcontos. Do you want to get such a miracle too? To make a reliable drawer for carrying the frames with their own hands, you do not need to spend a lot of effort or means.

What should be the box?

Our box for transferred by honey frames should be quite roomy, easy, and have special belt mounts (so that it is easier to carry it in the apiary). Another requirement is an even straight cover, which will continue to use the box as a comfortable chair.

In one such drawer, 8 frames are placed (based on the suggested sizes in the drawing). It is possible to increase its capacity by correcting the sizes, but then it will be hard to transfer it. The total weight of the filled container on 8 frames will be more than 10 kg, without taking into account the weight of the structure itself. The following photo is an exemplary model of such carrying.

How to make it yourself?

To make with their own hands Ramskonos, it will take some time and, of course, the right raw material for its manufacture. Do not take heavy materials, because all this will eventually affect the weight of the finished product. Be sure to think about how your box for the framework will be closed. Take materials with a margin, you may need to make not one, but two or more products. With their help in the flow of a beekeeper, there will always be order, and the framework does not have to carry hands.

Tools and materials

  • Materials for the box will require the following: plywood sheets with a thickness of at least 4 mm, as well as rails, 45x20 mm sizes (they will bent inside and outside). Another type of material is not suitable due to the severity of the product.
  • But if you are planning a box to use and like a garden chair of a beekeeper - take the sheets of chipboard, the thickness of the product will increase in this case. We will tell about the manufacture of plywood, designed for eight frames.

  • In addition to plywood sheets and rails, self-tapping screws or thin shoal nails will also need (they are more convenient to carefully score into a subtle plywood).
  • Also need an outdoor fastening that will hold the lid so that it does not open on the go and loops for folding it. Galvanized scrap (is shown in the photo below), and for internal - ordinary small loops, two pieces.
  • And the last detail is the belt and the outer attachments for it. They are attached to the self-tapping screws, like loops inside. Mounts can be taken stainless, and the belt will buy a nylon.

To seal the box, you can stick to the thermolent over the entire internal perimeter of the cover (with a tolerance from the edge to the width of the walls - 4 mm). This thermolent is sold as a insulation for windows for the winter and there can be different thickness - we need the thinnest, about 1 mm thick. It does not concern the framework, which means it does not get dirty and will not be sticky. In addition, a sealed box for a while can be left near the hives, as it will not get free to the frame of the bee.

However, the ventilation hole at the bottom of the case can still be done so that the honey does not "hit", just be sure to close it with a small grid. The grids will need a very small piece that can be attached by the usual construction stapler.

Instructions for manufacture

So, then a step-by-step instruction for designing a box for a frame or frame carrying.

  1. In total, there are six component parts in Ramconos - it is anterior, rear and two side panels, cover and bottom. Size walls (300x330).
  2. The first one should assemble the front wall, and then rear.
  3. From the edge of the front wall from above, 15 mm retreat and nail a pre-prepared rail (length 300, width 45, height 20 - dimensions in mm). This is our future focus for the framework, that is, the folds. Such two plates are nailed from the outside - without indents.
  4. If you plan to make a vent hole in the front, you need to cut it in advance. However, many beekeepers cost them without it.
  5. The rear wall is identical to the dimensions of the front, the rails are stuffed only outside - at the top and bottom without indents from the edges.
  6. The side walls of the same dimensions (300x330) are narrowed from the front and rear, and after they are also stuffed onto their outer surface along two rails - from above and below. So it will be convenient to take a drawer in hand.
  7. Next is going to the lid, attached to the loop. Its dimensions are indicated in the drawing.
  8. The bottom is measured around the perimeter and is knocked with nails, after which the closing part of the fasten is screwed to the lid, and the stationery is fixed part of the fasten. Detailed drawings, as well as a general view of the product, can be considered further in the photo.
Photo 1. Front Wall CarryingPhoto 1. Front panel drawing
Scheme side panelPhoto 2. Side panel drawing
Drawing of the lid of Ramakonos.Photo 3. Drawing of the lid of the Ramakonos
General Ramconos Assembly SchemePhoto 4. General Ramconos assembly scheme

Thus, you will get a comfortable, tightly closing design, which can be left near the hive, without fear for the safety of collected honey.

Some frameworks of Ramakonos apply both as a trap for a roa, lubricating the bees there as a temporary dwelling. The idea of ​​such a temporary replacement of the hive drawer is pretty good. So solve yourself, whether you will also use your carrying.

Video "Box for socks frames"

Useful video in which it is described in detail how to independently assemble a multifunction box to work at the apiary.

For the convenience of the health profession from the hives, the beekeepers of all over the world use various patterns of carrying or, as they are also called, Ramcontos. Do you want to get such a miracle too? Then we suggest you to find out how to make a reliable box to carry the frames with your own hands without special expenses on expensive materials.

Our box for transferred by honey frames should be quite roomy, easy, and have special belt mounts (so that it is easier to carry it in the apiary). Another requirement is an even straight cover, which will continue to use the box as a comfortable chair.

In one such drawer, 8 frames are placed (based on the suggested sizes in the drawing). It is possible to increase its capacity by correcting the sizes, but then it will be hard to transfer it. The total weight of the filled container on 8 frames will be more than 10 kg, without taking into account the weight of the structure itself. The following photo is an exemplary model of such carrying.

What is Ramonos.

Various manipulations with frames - an integral part of beekeeping. It is possible to alleviate such actions using a special box for transferring a frame that is called Ramonos. Design can be made independently. There are certain requirements for it and operating rules.

Requirements for Ramonosu

In order for Ramonos to be easily and convenient to use, the design must comply with certain requirements:

  • Ease - a heavy box will be impossible to operate, so it should be small (usually by 6-8 frames) and from lightweight material (more often);
  • Specific dimensions - they must correspond to the size of the frames used at the apiary;
  • Multifunctionality - In addition to transferring the framework, the design can be used for fishing;
  • convenience of carrying - it is necessary to provide a drawer with handles, belt;
  • Moisture resistance - such a property is ensured by impregnation with oil, it additionally increases the wear resistance of the product.

Ramonos can be used even for insect content, but only short-term. This option allows you to replace the special Roya, in the dark of which the bees are very worried.

Make yourself portable box for frames

Our Ramconos. consists of six main parts : front, rear, two side walls, as well as bottom and lids.

There is nothing complicated in the assembly. They collect the front and rear walls. On the inside at a distance of 15 mm from the upper edge, we screw the rail 300x45x20 - it will serve as a focus (fold). The first and rear walls are identical to each other.

In the front cut (or drill) the pilot.

Front wall Ramonos.

Then we make side walls and collect the ramos housing (screw them to the front and rear wall).

Side wall of Ramonos.

Next, we collect the lid of our Ramakonos. You can serve just carved a rectangular piece of plywood. You can come up from below something like legs, rails, etc.

Now we screw the bottom and hang the lid on the loop.

That's all right.

Everything should turn out very quickly. I did the focus on this, namely, the simplicity and speed of manufacture, as well as on the ease of the product.

Scheme of finished Ramonos trap

In early June I will write a detailed article about fishing.

Honey is not only a delicious, but also a very useful product. Today, the apiary is greatly successful. Quite often, the beekeeper appears the need to inspect the framework, so it is necessary for greater convenience, it is necessary to carry a box for carrying a frame (Ramonos). It can be bought, but make it my own hands will not be anything complicated. To do this, it is enough to have clear drawings, materials and desire to make.

The beekeeper often takes out a framework from the Ulytoletoby to make Ramakonos with their own hands, it will take some time and, of course, the right raw material for its manufacture. Do not take heavy materials, because all this will eventually affect the weight of the finished product. Be sure to think about how your box for the framework will be closed. Take materials with a margin, you may need to make not one, but two or more products. With their help in the flow of a beekeeper, there will always be order, and the framework does not have to carry hands.

Tools and materials

  • Materials for the box will require the following: plywood sheets with a thickness of at least 4 mm, as well as rails, 45x20 mm sizes (they will bent inside and outside). Another type of material is not suitable due to the severity of the product.
  • But if you are planning a box to use and like a garden chair of a beekeeper - take the sheets of chipboard, the thickness of the product will increase in this case. We will tell about the manufacture of plywood, designed for eight frames.

  • In addition to plywood sheets and rails, self-tapping screws or thin shoal nails will also need (they are more convenient to carefully score into a subtle plywood).
  • Also need an outdoor fastening that will hold the lid so that it does not open on the go and loops for folding it. Galvanized scrap (is shown in the photo below), and for internal - ordinary small loops, two pieces.
  • And the last detail is the belt and the outer attachments for it. They are attached to the self-tapping screws, like loops inside. Mounts can be taken stainless, and the belt will buy a nylon.

To seal the box, you can stick to the thermolent over the entire internal perimeter of the cover (with a tolerance from the edge to the width of the walls - 4 mm). This thermolent is sold as a insulation for windows for the winter and there can be different thickness - we need the thinnest, about 1 mm thick. It does not concern the framework, which means it does not get dirty and will not be sticky. In addition, a sealed box for a while can be left near the hives, as it will not get free to the frame of the bee.

However, the ventilation hole at the bottom of the case can still be done so that the honey does not "hit", just be sure to close it with a small grid. The grids will need a very small piece that can be attached by the usual construction stapler.

Instructions for manufacture

So, then a step-by-step instruction for designing a box for a frame or frame carrying.

  1. In total, there are six component parts in Ramconos - it is anterior, rear and two side panels, cover and bottom. Size walls (300x330).
  2. The first one should assemble the front wall, and then rear.
  3. From the edge of the front wall from above, 15 mm retreat and nail a pre-prepared rail (length 300, width 45, height 20 - dimensions in mm). This is our future focus for the framework, that is, the folds. Such two plates are nailed from the outside - without indents.
  4. If you plan to make a vent hole in the front, you need to cut it in advance. However, many beekeepers cost them without it.
  5. The rear wall is identical to the dimensions of the front, the rails are stuffed only outside - at the top and bottom without indents from the edges.
  6. The side walls of the same dimensions (300x330) are narrowed from the front and rear, and after they are also stuffed onto their outer surface along two rails - from above and below. So it will be convenient to take a drawer in hand.
  7. Next is going to the lid, attached to the loop. Its dimensions are indicated in the drawing.
  8. The bottom is measured around the perimeter and is knocked with nails, after which the closing part of the fasten is screwed to the lid, and the stationery is fixed part of the fasten. Detailed drawings, as well as a general view of the product, can be considered further in the photo.

Thus, you will get a comfortable, tightly closing design, which can be left near the hive, without fear for the safety of collected honey.

Some frameworks of Ramakonos apply both as a trap for a roa, lubricating the bees there as a temporary dwelling. The idea of ​​such a temporary replacement of the hive drawer is pretty good. So solve yourself, whether you will also use your carrying.

Production version number 2.

The size of the box, where the 6 frames will be included, the following: 470x300 mm (DHSH). Depending on the size of the frames themselves, Ramonos parameters are calculated. For example, if the width is 37 mm, then the product will have a width of 222 mm. To calculate the parameter, the width of one frame must be multiplied by their number. All side planks are better made from the board whose width is 20 mm. For the walls, take the phaneer with a thickness of 4 mm. It is attached with the help of ordinary lack of wooden wooden planks.

Before proceeding with the preparation of materials, it is necessary to develop a drawing with concrete sizes. . The height of the drawer for storing a frame produced by their own hands is done with a small margin of 50 mm, so the final design height is 350 mm. Experienced beekeepers are recommended to multiply by the number of frames rounded width (i.e. not 37, and 40 mm).

The length of the product will depend on the boards used, or rather from their thickness. On average, a size is taken equal to 510 mm. Thus, the carrying for the framework will have the following parameters: 510x350 mm. With the help of a screwdriver gently collect the product.

For the bottom and the lid is taken by a plywood in 4 mm thick. To cut these parts only after assembling the main sides of the frame storage box. Otherwise, it is possible to make a mistake in the calculations and not take into account the thickness of the planks used. Ultimately, the bottoms will be attached to the boards, which will make the design stronger and reliable. The cover of the product must fit tightly, so the dimensions of the planks must fully correspond to the internal perimeter of the drawer. It is there that they subsequently will be stuffed.

From both sides, the handles are screwed to the box so that it can be free to move it freely. To do this, install brackets and stretch the sling, which the node is tied after the tension. The node itself should be pushed to the brackets so that in the future it does not interfere. Make it is necessary so that you can hang the row on the shoulder. After all, sometimes the box reaches 20 kg in weight, and it is quite difficult to carry such a cargo. Frames with honey are rather heavy and sometimes reach 5 kg (the frame "Dadan").

Drawing of the box for transferring frames in transverse (A) and longitudinal cuts (b)

Functionality of the product

So that there were no problems with the delivery of the box from the hive, it is necessary to make it from plywood, thanks to which the framework with all the contents to get much more convenient and easier. There are 6 frames in the box. After seizures, the hive closes.

  • pick up the necessary materials and tools;
  • Think over connecting works;
  • collect elements into a single integer;
  • fasten the handles;
  • Covered by a protective composition.

The parameters of the box are small. In length from 455 mm; in width - 235 mm; In height - 320 mm.

The frames carried by the drawer are different, so after each application they need to be disinfected. Due to the accumulation of moisture on the plywood and in order to avoid the speedy wear of the product, the material is impregnated with oil. The box itself is installed near the hive or behind it, so that you can put the frames there during honey pumping. The box should be not heavy, but strong, so that during operation he has not broke.

Ten Frame Box

How in beekeeping use boxes

In addition to the storage of the frames themselves, the design applies for other purposes. For example, for the roo content. The beekeepers consider it the best option than a special Roya, in which bees often suffer concern because of a long stay in the dark. Roy is placed directly on the frame after its withdrawal. The design itself is installed next to the hives. The uterus itself should be located directly on the frame, and others can shake on a pre-prepared lower frame. But even in such a box it is not recommended for a long time to contain insects.

MEDY BACK

Constructive feature of the box for two people is that it has several large sizes. There is placed already from 20 to 22 frames from the hive. Dimensions of such Ramonos: 900x800 mm. Such a large design can be further stored for anything. One butcher with such a box will not cope. The design itself should be very durable, so the end boards must have a good thickness. For the connection it is better to use nails. With the help of screws, side planks of the top with the walls are connected. On the side of the lower part directly to the edges of the plank is nailed. In complete with the ends the handles are attached. Workers of beekeeping farms use such structures as temporary hives.

It should be noted that it is quite simple to make the design for the content of the framework. To do this, you should have an accurate drawing and a consistent action plan. The correct approach to business will save you from many problems and will greatly relieve work. In the future, such boxes are convenient to adapt to the temporary additional hive.

View of the working drawer from the inside

The bottom and the cover are cut in size from 4-millimeter plywood. The dimensions are better to determine with the help of a roulette when the box will already be collected, because In advance it will be impossible to take into account the thickness of the planks (rigidity).

If the size length is 510 mm, then in thickness it will turn on: the thickness of the board, plywood and planks stuffed on the phaneer. It is necessary to take into account this, because it is to the planks (and sideboards) the bottom will be attached - so the design will be tougher. It is necessary to fill the inner side of the lid, which will correspond to the internal perimeter of the working box.

So the lid will close tightly.

Why didn't I use the loop? Sometimes when working, it is necessary to open the cover on the loop, the additional space is needed, but by and large - this is a matter of habit. It is more convenient for me to work with such a lid.

For carrying a box, you must provide handles. I made one one. On the side boards, I nailed powerful brackets and handed the line through them.

The result was the following:

I just handed the ring and tied the knot. The knot tried to put closer to the bracket so that he would not interfere with when working.

Transfer of a working drawer in hand

Why did I use this method of carrying? Yes, very simple. Most often I use the working box for carrying frames. And everyone knows that the framework, especially with honey, is heavy. Judge for yourself. Rutta's full-fledged frame has a mass of 3-3.5 kg, the Dadan frame is 4-5 kg. And if these frames are at least four, the mass increases to 14-16 kg. In the hands of this weight, you can drag ... two times. And if a lot of frames?

The sling can also hang on the shoulder and distribute the load.

Transfer of a working drawer on the shoulder

For something you can still use the working box

In addition to carrying the framework to the working box, I plant a swarm. It is understood that for ROOV specially invented Roya. But I like working with a working box more. I will explain why. A couple of times I used ROOV. Bees behaved restlessly. They had to be withstanding for a long time in a dark place, and once the swarm from me simply "escaped."

To catch the swarm, I take a working box and put 3-4 frames there, it is better that at least in one of them was honey.

And here with this "wealth" I climb on the tree where Roy was invented. Uncomfortable, I agree. And what verbal momentum I'm talking when I climb on a tree ... Every time I stubbornly proving myself that I am not right and is much easier with Roast. Apparently I regain.

Most often, I leave the working box on the nearest fork, pull out one of the frames and gently put it on the swarm and just waiting. In 90% of cases, the bees begin to actively transfer to the frame. You can substitute the frame from below and throw onto it the main mass of bees. The main thing that the uterus is on the framework. And then it all depends on how many bees it is necessary to guess that the uterus on the branch is no longer. Many times I had cases when I put the frame to the working box and all bees ranked in it. The branch remained either the most stubborn or the most closestly. It happened that I set the working box under the tree (when the uterus was already in the working box) and watched an amazing picture when Roy starred from the branch and climbed into the box.

It doesn't make sense to withstand in the box of bees for a long time. It is enough of that time that is necessary to prepare a new place for Roy and install the housing. Bees neatly on the framework are transplanted into a new home and in a few minutes begin to nourish.

To add a comment - Sign up!

Rules of operation and care

Ramonos - the design is quite simple, but requiring some care:

  • Disinfection. It should be carried out after each operation of the design.
  • Carrying. To ventilate Ramonos not only before the first operation, but in the future. Bees to smells are very sensitive.
  • Before exploitation of Ramonos, it is recommended to complain its attractive herbs for bees.
  • Ramonos is a wood product, so it is necessary to store it accordingly. At the storage location should be sufficiently sufficient, strong differences of moisture and temperature should be avoided.
  • Use when roding. In this case, in Ramonos, you must put a pair of frames with dryness, and then shake the bees. The design cover and the pilots are necessarily closed. Ramonos leave in a cool place for the night. Competently organized ventilation will provide insects with the necessary air, and also reduce the temperature inside Ramonos - it acts soothing on insects.

Ramonos is often referred to as a worker or universal box. This design at the apiary is very convenient and greatly facilitates a number of works. You can make it yourself - all materials and actions are simple. Properly executed design ensures its multifunctionality.

Evaluate Article.

[Total: Average:]

Any beekeeping when working with bees, you must have a working box, which, if necessary, you can put a certain number of frames. Especially such a box is needed when pumping honey.

  • It is better to do the working box, because sometimes you want to sit down and relax, and there is nothing nearby in bars.
  • Collecting your working box, I proceeded from the fact that it should be not very heavy, since when carrying a honey frame mass and so large enough.
  • My working box is designed for 6 frames (470 * 300).
  • Frame Carrying Box (Ramonos) DIY

Box. Appearance.

Since the width of one frame is 37 mm, then the width of the box should be 37 * 6 = 222 mm, and it is better a little more to make it easier to put the framework, especially if they are reflected, i.e. 23-24 cm.

I made the side walls from the broad "twenty". I had one suitable board, but even if there is no such wide board, you can use ordinary boards, collecting them in a quarter, in a spike or swallow tail. This is someone as you like.

For the side walls, I used a thin paneur (4 mm), reinforced by the perimeter with thin wooden planks.

Frame Carrying Box (Ramonos) DIY

  1. Calculate the size of the working box:
  2. Height: 300 + 50 = 350 mm (height stock)
  3. Width: 37 * 6 = 222, but it is better to 40 * 6 = 240 mm (my suitable board turned out to be 23 cm, which is also not bad).

Length of lateral parts: 470 + 2 * 20 (thickness of the board) = 510 mm. You can make a small stock of 5 mm. Those. The dimensions of plywood will be 510x350.

The dimensions of the planks that make up the ribs of stiffness around the perimeter of plywood are not critical.

Collective box is very simple. With the help of a screwdriver, twist 2-3 screws in height in the end of the side board.

Frame Carrying Box (Ramonos) DIY

View of the working drawer from the inside.

The bottom and the cover are cut in size from 4-millimeter plywood. The dimensions are better to determine with the help of a roulette when the box will already be collected, because In advance it will be impossible to take into account the thickness of the planks (rigidity).

If the size length is 510 mm, then in thickness it will turn on: the thickness of the board, plywood and planks stuffed on the phaneer. It is necessary to take into account this, because it is to the planks (and side boards) a bottom will be attached - so the design will be tougher.

On the inside of the lid, it is necessary to fill the planks that will correspond to the internal perimeter of the working box.

Frame Carrying Box (Ramonos) DIY

So the lid will close tightly.

Why didn't I use the loop? Sometimes when working, it is necessary to open the cover on the loop, the additional space is needed, but by and large - this is a matter of habit. It is more convenient for me to work with such a lid.

For carrying a box, you must provide handles. I did one.

  • On the side boards, I nailed powerful brackets and handed it out through them.
  •  Frame Carrying Box (Ramonos) DIYFrame Carrying Box (Ramonos) DIY
  • The result was the following:

Frame Carrying Box (Ramonos) DIY

I just handed the ring and tied the knot. The knot tried to put closer to the bracket so that he would not interfere with when working.

Frame Carrying Box (Ramonos) DIYTransfer of a working drawer in hand

Why did I use this method of carrying? Yes, very simple. Most often I use the working box for carrying frames. And everyone knows that the framework, especially with honey, is heavy. Judge for yourself. Rutta's full-fledged frame has a mass of 3-3.5 kg, the Dadan frame is 4-5 kg. And if these frames are at least four, the mass increases to 14-16 kg. In the hands of this weight, you can drag ... two times. And if a lot of frames?

  1. The sling can also hang on the shoulder and distribute the load.
  2. Frame Carrying Box (Ramonos) DIYTransfer of a working drawer on the shoulder
  3.  What else can I use the working box?

In addition to carrying the framework to the working box, I plant a swarm. It is understood that for ROOV specially invented Roya. But I like working with a working box more. I will explain why. A couple of times I used ROOV. Bees behaved restlessly. They had to be withstanding for a long time in a dark place, and once the swarm from me simply "escaped."

To catch the swarm, I take a working box and put 3-4 frames there, it is better that at least in one of them was honey.

And here with this "wealth" I climb on the tree where Roy was invented. Uncomfortable, I agree. And what verbal momentum I'm talking when I climb on a tree ... Every time I stubbornly proving myself that I am not right and is much easier with Roast. Apparently I regain.

Most often, I leave the working box on the nearest fork, pull out one of the frames and gently put it on the swarm and just waiting. In 90% of cases, the bees begin to actively transfer to the frame. You can substitute the frame from below and throw onto it the main mass of bees. The main thing that the uterus is on the framework.

And then it all depends on how many bees it is necessary to guess that the uterus on the branch is no longer. Many times I had cases when I put the frame to the working box and all bees ranked in it. The branch remained either the most stubborn or the most closestly.

It happened that I set the working box under the tree (when the uterus was already in the working box) and watched an amazing picture when Roy starred from the branch and climbed into the box.

It doesn't make sense to withstand in the box of bees for a long time. It is enough of that time that is necessary to prepare a new place for Roy and install the housing. Bees neatly on the framework are transplanted into a new home and in a few minutes begin to nourish.

To add a comment - Sign up!

A source: http://pchelolubitel.ru/praktika/28-rabochij-yashchik-svoimi-rukami.

Ramonos Ramonos trap. Drawing

Frame Carrying Box (Ramonos) DIYHello dear beekeepers! May holidays passed. Weather pleased more and more. Very soon, at the end of May - the beginning of June will begin a turning time, which means that it's time to think about trappers for stray ROOV. Today I want to publish the drawings for which they are very easy to make. Maybe someone will come in handy.

Friends, I will say to you honestly: I myself have never been doing stray root. Last year, he made one trap, but she did not let her. There were no causes (or excuses), and there was no need to expand the apiary.

Now, in 2013, the circumstances were somewhat different and not in my favor.

I had to part with my partner, to leave him everything that was acquired by the "unbearable work" and began to say anew, "from scratch", having only a certain luggage of knowledge, skills and skills.

That's why I need straightened swarms now. This is a very profitable way to purchase bees, which does not require practically no cash infusion.

Well,, the theory of fishing, I seem to know, so I will check her a little later in practice. Be sure to write about it later the article.

Let's go back to our traps.

Very many beekeepers producing traps, use them only for direct intended. I think this is not entirely rational (unless of course they are made not from a solid piece of lounge or throwing material). After all, the rooke time, as a rule, ends with the beginning of the main bribe, and this is July month (in most regions). In August, time to pump off honey.

And why don't we use ours who have already spent their traps this year, as Ramonos (boxes for transferring frames)? That's quite possible. Moreover, it often happens that there is a lot of Ramarkosov (5-6), and there are only 1-2 of them at an apiary. In addition, it is possible both as a temporary container for melting. In general, it will not be superfluous.

Additional inventory at the beekeeper does not exist.

Now more.

Frame Carrying Box (Ramonos) DIY

Ramonos - trap for bees

My choice fell on the eight-hand trap for Dadanovsky frames. Why is that? I think that eight frames are the optimal amount: and not much and not enough. If you make small volume traps, then strong swarms can bypass them - close dwelling themselves.

For the manufacture of Ramonos with their own hands, I chose Phaneur with a thickness of 4 mm and a rail of 45mm x 20mm.

In general, you can use something else (last year I did from the chipboard, but it turned out to be difficult), to recalculate the sizes, I think it will not be much difficulty.

It is possible, of course, that the thickness of plywood is 4 mm is small and there will be insufficient thermal insulation, because of which during the summer bake, the bees will be required to ventilate the socket, but I think for temporary housing.

We will also need a vehicle self-tapping screws (you can use nails), loops for a folding lid. You still need to think about how you will fix the lid in the closed position. I looked at this composure, which before used to fix the buildings of wooden hives to each other.

For Ramonos, we need a belt belt. In my opinion it is better nylon. It is sold for a honey in construction stores at an affordable price.

On the plane, where the lid falls on the body itself, you can stick the strip of tape, which is used to seal window frames in winter. It is made from the material similar to the foam rubber. The thickness of it is about a millimeter. It will contribute to a more sealed joint and reliable fit of the cover to the body of our trap.

I prefer a round with a diameter of about 30 mm, so as not to use factory pilot barrafficers. It is closed by a tube of wood (a stubbed knife with a knife from a shovel for example), wrapped for better tightness with a tape.

  • From the back, you can consider some ventilation hole for transportation.
  • Well, that's all you need to foresee.
  • Details need to be customized to each other better so that when transporting the bee has not flowed and there were no surprises.
  • Our Ramconos. consists of six main parts : front, rear, two side walls, as well as bottom and lids.
  • There is nothing complicated in the assembly.

First we collect the front and rear walls. On the inside at a distance of 15 mm from the top edge, we screw the rail 300x45x20 - it will serve as a focus (fold).

The front and rear walls are identical to each other. In the front cut (or drill) the pilot.

Frame Carrying Box (Ramonos) DIY

Front wall Ramonos.

Then we make side walls and collect the ramos housing (screw them to the front and rear wall).

Frame Carrying Box (Ramonos) DIY

Side wall of Ramonos.

Frame Carrying Box (Ramonos) DIY

Ramonos cover

Next, we collect the lid of our Ramakonos. For us, we will serve just carved the size of a rectangular piece of plywood. You can come up from below something like legs, rails, etc.

Now we screw the bottom and hang the lid on the loop.

Frame Carrying Box (Ramonos) DIY

Components

That's all right.

Everything should turn out very quickly. I did the focus on this, namely, the simplicity and speed of manufacture, as well as on the ease of the product.

Frame Carrying Box (Ramonos) DIY

Scheme of finished Ramonos trap

In early June I will write a detailed article about fishing.

Frame Carrying Box (Ramonos) DIY

Thank you for caught! Successes in the beeness!

P.S. If something in the scheme, something incomprehensibly painted that write in the comments or by mail.

Sincerely, Nikolai Tatarenkov.

But the interesting way to catch a swarm literally on the fly !! And no traps are needed)) We look:

A source: http://p4elovek.ru/ramonos-lovushka-dlya-roev-chertezh/.html.

Homemade Honey Frames filled with honey

For the convenience of the health profession from the hives, the beekeepers of all over the world use various patterns of carrying or, as they are also called, Ramcontos. Do you want to get such a miracle too? To make a reliable drawer for carrying the frames with their own hands, you do not need to spend a lot of effort or means.

Our box for transferred by honey frames should be quite roomy, easy, and have special belt mounts (so that it is easier to carry it in the apiary). Another requirement is an even straight cover, which will continue to use the box as a comfortable chair.

In one such drawer, 8 frames are placed (based on the suggested sizes in the drawing). It is possible to increase its capacity by correcting the sizes, but then it will be hard to transfer it. The total weight of the filled container on 8 frames will be more than 10 kg, without taking into account the weight of the structure itself. The following photo is an exemplary model of such carrying.

Frame Carrying Box (Ramonos) DIY

How to make it yourself?

To make with their own hands Ramskonos, it will take some time and, of course, the right raw material for its manufacture. Do not take heavy materials, because all this will eventually affect the weight of the finished product.

Be sure to think about how your box for the framework will be closed. Take materials with a margin, you may need to make not one, but two or more products.

With their help in the flow of a beekeeper, there will always be order, and the framework does not have to carry hands.

Tools and materials

  • Materials for the box will require the following: plywood sheets with a thickness of at least 4 mm, as well as rails, 45x20 mm sizes (they will bent inside and outside). Another type of material is not suitable due to the severity of the product.
  • But if you are planning a box to use and like a garden chair of a beekeeper - take the sheets of chipboard, the thickness of the product will increase in this case. We will tell about the manufacture of plywood, designed for eight frames.

Frame Carrying Box (Ramonos) DIY

  • In addition to plywood sheets and rails, self-tapping screws or thin shoal nails will also need (they are more convenient to carefully score into a subtle plywood).
  • Also need an outdoor fastening that will hold the lid so that it does not open on the go and loops for folding it. Galvanized scrap (is shown in the photo below), and for internal - ordinary small loops, two pieces.
  • And the last detail is the belt and the outer attachments for it. They are attached to the self-tapping screws, like loops inside. Mounts can be taken stainless, and the belt will buy a nylon.

To seal the box, you can stick to the thermolent over the entire internal perimeter of the cover (with a tolerance from the edge to the width of the walls - 4 mm).

This thermolent is sold as a insulation for windows for the winter and there can be different thickness - we need the thinnest, about 1 mm thick. It does not concern the framework, which means it does not get dirty and will not be sticky.

In addition, a sealed box for a while can be left near the hives, as it will not get free to the frame of the bee.

Frame Carrying Box (Ramonos) DIY

However, the ventilation hole at the bottom of the case can still be done so that the honey does not "hit", just be sure to close it with a small grid. The grids will need a very small piece that can be attached by the usual construction stapler.

Instructions for manufacture

So, then a step-by-step instruction for designing a box for a frame or frame carrying.

  1. In total, there are six component parts in Ramconos - it is anterior, rear and two side panels, cover and bottom. Size walls (300x330).
  2. The first one should assemble the front wall, and then rear.
  3. From the edge of the front wall from above, 15 mm retreat and nail a pre-prepared rail (length 300, width 45, height 20 - dimensions in mm). This is our future focus for the framework, that is, the folds. Such two plates are nailed from the outside - without indents.
  4. If you plan to make a vent hole in the front, you need to cut it in advance. However, many beekeepers cost them without it.
  5. The rear wall is identical to the dimensions of the front, the rails are stuffed only outside - at the top and bottom without indents from the edges.
  6. The side walls of the same dimensions (300x330) are narrowed from the front and rear, and after they are also stuffed onto their outer surface along two rails - from above and below. So it will be convenient to take a drawer in hand.
  7. Next is going to the lid, attached to the loop. Its dimensions are indicated in the drawing.
  8. The bottom is measured around the perimeter and is knocked with nails, after which the closing part of the fasten is screwed to the lid, and the stationery is fixed part of the fasten. Detailed drawings, as well as a general view of the product, can be considered further in the photo.

Frame Carrying Box (Ramonos) DIYPhoto 1. Front panel drawing Frame Carrying Box (Ramonos) DIYPhoto 2. Side panel drawing Frame Carrying Box (Ramonos) DIYPhoto 3. Drawing of the lid of the Ramakonos Frame Carrying Box (Ramonos) DIYPhoto 4. General Ramconos assembly scheme

Thus, you will get a comfortable, tightly closing design, which can be left near the hive, without fear for the safety of collected honey.

Some frameworks of Ramakonos apply both as a trap for a roa, lubricating the bees there as a temporary dwelling. The idea of ​​such a temporary replacement of the hive drawer is pretty good. So solve yourself, whether you will also use your carrying.

Video "Box for socks frames"

A source: https://zoohoz.ru/pchelovodstvo/uli/yashhik-dlya-perenoski-ramok-12151/

Construction of a beecopter with their own hands

Frame Carrying Box (Ramonos) DIY

For long-term transportation, insect transportation is customary to use reliable beeflakes. This is a peculiar design that enlists the bee family and everything you need for them. The beeopacket is the same hive, but it is characterized by simplicity of structure, minimum ventilation and free space, which are extremely necessary for prosperous transportation.

Features of the design of the pchelopeta

The beecapacuit can actually make with their own hands what will be more cheaper than buying on the market. Basically, they are created on six or four frames. Perhaps you are looking for information about how to make a frame for bees. The main condition is a powerful and durable mount in the lower, upper parts of the frame.

Thus, it is possible to prevent damage in the process of transportation. There is a special GOST standard for a cellular package containing a bee family. He notes the boundaries, permissible characteristics and norms.

The table below presents the GOST standards on the borders and standards of different beeworks:

Frame Carrying Box (Ramonos) DIY

There are special designs for transportation - boxes for beeworks. They are divided into non-removal, cellular. Modern beekeeping prefers to use cellular packages for which the corresponding box can be made.

The size can be different, as well as the size of the framework. The beekeeper can make them with his own hands using the drawing, as well as given its own wishes, tastes and preferences. This is the main advantage of making a drawer with their own hands.

Package construction scheme:

Frame Carrying Box (Ramonos) DIY

Package details: 1 - Top combed; 2 - the grave is lower; 3 - Barbed with a notch; 4 - plate with recess; 5 - plate with recess; 6 - lid; 7 - the wall of the feeder side; 8 - Petal of the Willow.

You can accommodate a special box under the framework of the required size, since all the hives are different. The beekeeper must rely on personal experience when creating a box. Before you understand the description of the drawing and size in more detail, you need to determine the fundamental components that are necessary for the design of the box.

It should be present:

  • feeder;
  • appropriate fastening under the frame, namely on top and bottom;
  • empty space between the frames;
  • Ventilation holes.

Builder construction with your own hands

Frame Carrying Box (Ramonos) DIYCell Package for Transportation Bees: 1 - Bar 15x19x520 (8 pcs.); 2 - Bar 15x19x200 (9 pcs.); 3 - Top comb (2 pcs.); 4 - plate 4x200x330 (1 pc.); 5 - Bar 15x19x390 (8 pcs.); 6 - Grooming the bottom (2 pcs.); 7 - Bar 15x19x160 (2 pcs.); 8 - plate 4x20x100 (4 pcs.); 9 - Bar 15x19x240 (4 pcs.); 10 - plate 4x20x160 (1 pc.); 11 - plate with recess (1 pc.); 12 - Cellular frame; 13 - nail 2x45; 14 - nail 1.6x40; 15 - mesh 120x200 (2 pcs.); 16 - cell; 17 - nail 1.8x32; 18 - nail 1.2x20; 19 - plate 4x20x70 (1 pc.); 20 - Bar with notch (1 pc.).

Make a bee package with your own hands just enough and under the power to any poker, if it is a little aimed in this area. It is better to use fiberboard as material. This is due to the fact that such raw materials are easy and inexpensive, additional processing is not required for it. The butter can independently adjust the width, depth and height of the bee package, as well as determine the wall thickness.

Thematic literature contains a huge number of drawings, accurate and detailed schemes. They have strict parameters, fastening methods, as well as the smallest details and details.

In addition, you can find useful training videos and benefits that will greatly facilitate the solution of a given goal. At first it is worth determining which parts are necessary for the structure, as well as calculate their parameters.

These processes are very important during the preparatory phase.

The main components of the cellular package are:

  • bar;
  • top, bottom comb;
  • cell frame;
  • cell;
  • plate containing the recess;
  • grid;
  • plate;
  • Nails.

Frame Carrying Box (Ramonos) DIYCell Package (transverse section): 1 - Bar 15x19x520 (8 pcs.); 2 - plywood plate 4x240x520 (2 pcs.); 3 - plate 4x430x520 (2 pcs.); 4 - lower comb; 5 - upper comb; 6 - clamping bar.

In the absence of time or desire to build a drawer with their own hands, you can turn to the beekeeper, which was acquired by a bee family. Do it in advance so that the seller can prepare. You can also use information about the difference between beekeepings from the bellow.

A source: https://pacechnyk.ru/pchelovodstvo/o-pchelah/kak-sdelat-pchelopaket.html.

We make an independently portable box for frames with your own hands

Honey is not only a delicious, but also a very useful product. Today, the apiary is greatly successful.

Quite often, the beekeeper appears the need to inspect the framework, so it is necessary for greater convenience, it is necessary to carry a box for carrying a frame (Ramonos).

It can be bought, but make it my own hands will not be anything complicated. To do this, it is enough to have clear drawings, materials and desire to make.

Frame Carrying Box (Ramonos) DIY

Beekeeper often takes out frames from the hive

Functionality of the product

So that there were no problems with the delivery of the box from the hive, it is necessary to make it from plywood, thanks to which the framework with all the contents to get much more convenient and easier. There are 6 frames in the box. After seizures, the hive closes.

Production Stages:

  • pick up the necessary materials and tools;
  • Think over connecting works;
  • collect elements into a single integer;
  • fasten the handles;
  • Covered by a protective composition.

The parameters of the box are small. In length from 455 mm; in width - 235 mm; In height - 320 mm.

The frames carried by the drawer are different, so after each application they need to be disinfected.

Due to the accumulation of moisture on the plywood and in order to avoid the speedy wear of the product, the material is impregnated with oil.

The box itself is installed near the hive or behind it, so that you can put the frames there during honey pumping. The box should be not heavy, but strong, so that during operation he has not broke.

Frame Carrying Box (Ramonos) DIY

Ten Frame Box

Production option

The size of the box, where the 6 frames will be included, the following: 470x300 mm (DHSH). Depending on the size of the frames themselves, Ramonos parameters are calculated. For example, if the width is 37 mm, then the product will have a width of 222 mm.

To calculate the parameter, the width of one frame must be multiplied by their number. All side planks are better made from the board whose width is 20 mm. For the walls, take the phaneer with a thickness of 4 mm.

It is attached with the help of ordinary lack of wooden wooden planks.

Frame Carrying Box (Ramonos) DIY

Appearance of the box inside

Before proceeding with the preparation of materials, it is necessary to develop a drawing with concrete sizes. .

The height of the drawer for storing a frame produced by their own hands is done with a small margin of 50 mm, so the final design height is 350 mm.

Experienced beekeepers are recommended to multiply by the number of frames rounded width (i.e. not 37, and 40 mm).

The length of the product will depend on the boards used, or rather from their thickness. On average, a size is taken equal to 510 mm. Thus, the carrying for the framework will have the following parameters: 510x350 mm. With the help of a screwdriver gently collect the product.

For the bottom and the lid is taken by a plywood in 4 mm thick. To cut these parts only after assembling the main sides of the frame storage box. Otherwise, it is possible to make a mistake in the calculations and not take into account the thickness of the planks used.

Ultimately, the bottoms will be attached to the boards, which will make the design stronger and reliable. The cover of the product must fit tightly, so the dimensions of the planks must fully correspond to the internal perimeter of the drawer.

It is there that they subsequently will be stuffed.

From both sides, the handles are screwed to the box so that it can be free to move it freely. To do this, install brackets and stretch the sling, which the node is tied after the tension.

The node itself should be pushed to the brackets so that in the future it does not interfere. Make it is necessary so that you can hang the row on the shoulder. After all, sometimes the box reaches 20 kg in weight, and it is quite difficult to carry such a cargo.

Frames with honey are rather heavy and sometimes reach 5 kg (the frame "Dadan").

Frame Carrying Box (Ramonos) DIY

Drawing of the box for transferring frames in transverse (A) and longitudinal cuts (b)

How do bins use in beekeeping?

In addition to the storage of the frames themselves, the design applies for other purposes. For example, for the roo content. The beekeepers consider it the best option than a special Roya, in which bees often suffer concern because of a long stay in the dark.

Roy is placed directly on the frame after its withdrawal. The design itself is installed next to the hives. The uterus itself should be located directly on the frame, and others can shake on a pre-prepared lower frame.

But even in such a box it is not recommended for a long time to contain insects.

MEDY BACK

Constructive feature of the box for two people is that it has several large sizes. There is placed already from 20 to 22 frames from the hive. Dimensions of such Ramonos: 900x800 mm. Such a large design can be further stored for anything. One butcher with such a box will not cope.

The design itself should be very durable, so the end boards must have a good thickness. For the connection it is better to use nails. With the help of screws, side planks of the top with the walls are connected. On the side of the lower part directly to the edges of the plank is nailed. In complete with the ends the handles are attached.

Workers of beekeeping farms use such structures as temporary hives.

It should be noted that it is quite simple to make the design for the content of the framework. To do this, you should have an accurate drawing and a consistent action plan. The correct approach to business will save you from many problems and will greatly relieve work. In the future, such boxes are convenient to adapt to the temporary additional hive.

A source: https://roypchel.ru/pchelovodstvo/yashhik-dlya-perenoski-ramok.html.

Ramakonos 6-frame Dadan without pocket

Frame Carrying Box (Ramonos) DIY Frame Carrying Box (Ramonos) DIY Frame Carrying Box (Ramonos) DIY Frame Carrying Box (Ramonos) DIY

Article: 00515

Ramakonos 6-frame Dadan without pocket

  • Ramakonos 6-frame without pocket.
  • Dimensions (mm): 300 × 325 × 525
  • Weight, kg): 3.75

Materials and elements used in the manufacture of goods: Ramakonos is a plywood box with a tight lid closed. Ramsonosa frame made of wooden rails 40 × 20 mm. For ease of transfer, a wide belt is used.

Description: Ramakonos is designed for temporary storage or transfer of a 6-frame Dadan, Ruta, or a store (see the frames for the hives).

Also, Ramakonos can be used to remove the vaccinated Roy, its transfer, short storage and transplants of the bee to the new hive.

Similar

If you can not visit our beekeeping shops in Moscow, Moscow region, St. Petersburg or Krasnodar, you have the opportunity to order delivery by phone or via the Internet to anywhere in Russia and the world, and payment to make any way convenient for you.

Selection is offered several ways of delivery:

  • Courier delivery
  • Russian Post
  • Motor transport our company
  • Independent transport companies

Especially for wholesale buyers "Adjourcing" offers products for beekeeping in wholesale and fine-winding prices with delivery in Russia, Kazakhstan, Belarus and Ukraine. Prices for wholesale goods You can clarify the manager with key clients during working hours by phone: 8 (800) 100-05-04 ext. 331.

LLC "Advanced Oceka" sells goods for beekeepers.

A source: https://pchelovodstvo.org/art00515.html

Drawing traps on 6 frames Dadan

This trap is intended for catching stray roes, in the period of rod.

Advantages of this trap:

  • Simplicity of design;
  • Cheapness;
  • Low weight.

Its volume allows you to catch quite large swarms, which can cover 6 frames of the Dadan system.

Material for manufacture:

  • plywood 4 mm;
  • Bruks (spruce, pine) with dimensions 15x15, 15x20, 15x30 mm of various lengths;
  • self-tapping screw or nails;
  • galvanized, tin or runner (by budget).

Anyone can easily make a trap with their own hands on 6 frames on the Dadan system. You can get an apiary for the singer of a penny, using a similar trap design!

General view of a trap on 6 frames

Assembly drawing of the end of the trap

The pilot can make any form. In the below drawing, the flyer has a size of 100x10 mm.

Drawings of bars to a trap on 6 frames

Before screwing into the bar Self-tapping screws, do not be too lazy to drill it with a thin drill, so you practically eliminate the splitting of bars.

Drawings of plywood details

Use the phaneer with a thickness of 4 mm, DVP, without special protection, should not be used in view of high hydroscopicity, as well as chipboard or cardboard.

Important! Do not save on the material, as good plywood, well-scratched outside, will serve you at least 10-12 years.

Painting it is necessary to perform with paints containing minimum odors, they include acrylic paint with a kel. Do not use oil paints, since so far they will unwind their smell, you can't really catch anything.

Successful catching and kind and honey bees!

Here are other drawings of traps

A source: https://medvkostrome.ru/lovuchka-na-6ramok/

To read

V. V. Tikhomirov

Beekeeping for beginners

Preface, or a brief explanation, why and why

If you, dear reader, decided to do beekeeping, you will find a fascinating journey into the world, which most people know little about. You will find knowledge that are expensive. Step by step, year after year you will move towards your goal.

Time will come, and once, coming out for an apiary, you will understand that your heart works smoothly, and not trembling, as in the first days. You will see that your movements have become accurate and neat. You all know, you can all. And books on beekeeping, when the bee sink outside the window, you can't shift convulsively.

You are calm and joy. And the sting of the bee brings you no pain, but health. And you feel sorry at this moment not myself, and the deceased on the protection of your dwelling bee. Because every one of them you love and as soon as you believe. If all this you find in yourself, knew, you became a beekeeper.

Well, while read about them, about bees.

On them, on the bees, the Lord God laid the concern for plant flowers. Having extradited herself, volley-unilies, they cross pollination, and as a result of the plant become a vitality, with high potential survival and fertility. Is there a lot or a little?

The answer will be very simple, if you submit our planet without paints of thousands of colors, plants, without summer smell of dispersion, without fruits and vegetables, without honey and wax, without many medicines, where beekeeping products are used. This will already be another land, on which humanity will remain only to live in his age, and not enjoy the world.

Invisibly for millions of people, forever immersed in urban life, but noticeable for those who live in the countryside at least in the summer, and even more so for those who decided to put in their garden even a few hives, life is firmly and forever connected with bees. Whether in the spring bee will visit your garden and garden, if not you, then the harvest is exactly dependent.

And those few who went deep into the study of the life of bees found their lives very reminiscent of the life of highly developed human society. And prepared for the winter crust and kindergartens, and care for the younger generation, and such a vertical of power, which is envy to many states.

Here you and our lungalist chosen by bees for several years. General and unconditional submission.

A regular army, ready to destroy the enemy and much more, ready to destroy the enemy and much more, which forced and forces me to treat the bees, not disseminately, as an unreasonable insect, and with deep reverence, as to the community vested with some intelligence.

Bees are preparing for

What is only one example from the life of bees. This happens infrequently, but nevertheless it happens. Shortly before the situation, the surroundings of the uterus thoughtfully frighten his ladies, fed, clean her wings, and it seems that it is time to fly away from the hive after ROOM.

Stepodo and important is the bee uterus on the arrive board, tries to take off, but for some reason only falls into the grass, where it is not necessary for anyone. There she will still die from hunger or under the foot of the beekeeper, because it does not know how to live on its own and live without his surroundings.

Arounded to fly? No, just its environment, based on its logic, feed it, but no wings cleaned, and strengthened. And here, the swarm, the involuntary conspiracy, not finding the uterus, returns back to the hive, wait until the power goes to the heir of the bee throne.

Isn't it reminding this environment of many large politicians, a quiet sack of fastening "wings" with their bosses? And such a "lucky" will be released on the attachment board of political elections, and the cuberance down. And his former environment is already arranged for the service for the new owner.

The resulting fact, as you understood, is not the only stated coincidence in the behavior of bees and people. And how many more secrets and questions in the life of bees, which man gives only approximate answers!

A novice beekeeper sometimes resembles a child who sent all his boiler energy to the solve one single secrecy - which is inside the toy and how its mechanism works there. It goes such a not young naturalist around a couple of newly acquired hives and worries, how are they there, poor bees, without him in the hives live? Is it enough for them? Is it warm? Do nectar wear?

There is a lot of energy in a person, and he begins in the case without him, from pure curiosity once a week check its apiary. Neighbors, if the bees did not get to them, in admiration. See what an experienced and competent beekeeper Ivan Ivanovich! I still understand in bees, I still know! You look, and the Medsk will pop up in autumn.

Ivan Ivanovich will open, I will get somehow a couple of frames, look at them carefully and back in the hive will deliver. While pulled out the frame, the tent of the bees crushed.

While she was turned over and something on it was noticed, the bees clung to his sleeves, to her feet and through protective clothes were pretty shy. Two dozen bees as it did not happen. Hurt your hands, and the frame back should be put. Hopes returned to the previous place and ran home. It is done.

The use of struck is obvious, hands swollen. Bees are fine. And know does not know that while he stuck in the nest frame, inadvertently crushed the uterus.

A few days later, he will prepare all the way, the pimentar will cut off hostile bees from his own person, will again make an autopsy and again will remain satisfied. True, it turns out that there is no honey in the ulle. Neither to yourself nor even bees. And the bees themselves in the ule are somehow not enough.

What remains to do? That's right, scold irregular bees. He invested the whole soul in them, and they, ungrateful ... swept on the seller of bees. Probably, the defective families hit him.

The year or two of solarms, and the beekeeping in a separate farm or the country area comes an end. The neighbors Ivan Ivanovich will explain that there is little time on the bees, things were tortured, and he will give his word more with insects not to contact.

"I won't buy a three-liter jar of honey? Do I need a lot? "

And it will not understand the main thing that if he left the bees at rest from the very beginning, he would not disturb the thermal regime in the nest, would not distract them from work, it would be now and with bees, and with honey.

Because the bee hive is the "black box" that lives in its laws and even any infrequent interference in it must be justified and neat. And experience, it does not immediately come.

It is believed that an experienced beekeeper can be called someone who is engaged in bees from five to fifteen years. Everyone has different abilities and everything is different in different ways to the top of skill.

Previously, beekeeping was very common fishery. Now skills transmitted from generation to generation beekeepers are almost lost. Now rarely when the beekeeper passes his inheritance skill. Most often, urban residents are uncomfortable when the pension and free time is not far from the mountain, which will be sorry to kill the TV.

Rate

Our book is intended to those who are just going to find skills who voluntarily agree to be an apprentice at the bees in the conditioned temporary segment from zero to (as it turns out), when not with whom, except for the book, and consult.

When you want to learn to understand, at what time do you need a hive, and when it is better to leave him alone. And once again, making the necessary actions, slowly acquire the skills of accurate and neat movements when working at the apiary.

It must be remembered that the bee, living next to you, in your ulle, does not get home. She never recognizes her owner in you and there will be no cheek, fly past you with a greeting. You are for her - a potential danger, robber and offender. Tens of millions of years lived bees without a person: the symbiosis of the bee and the person is invented not a bee, and therefore it requires respect.

A source: https://www.litmir.me/br/?b=220085&p=4

framework
framework

Hello dear friends!

To carry the frames, you must have at least one box. Size - under the standard frame. How many frames in it should be accommodated, solve themselves. Usually make on 10 -12 frames. As for me, it is better from 6 to 8 frames, such a box is easier and not too hard to wear. We have a box for 12 frames, which is not very convenient.

Frame Carrying Box Requirements
To make a box easily and conveniently work, he must have certain qualities.
Ease - a heavy box will not be able to operate, so it should be small (usually 6-8 frames) and from lightweight material;
Specific dimensions - they must correspond to the size of the frames used at the apiary;
Multifunctionality - In addition to transferring frames, the box can be used for fishing. Sushi storage;
Convenience of carrying - necessary. To make the drawer pens and belt;
Moisture resistance - such a property is provided by impregnation with oil and coating with its wax, additionally it increases the wear resistance of the drawer.
Stock Foto Yandex pictures pattern drawer shaping frame
Stock Foto Yandex pictures pattern drawer shaping frame

The best material for its manufacture - plywood. The box must have a lid, two handles and shoulders inside to put the frames. From the side of one of the ends of the box, it is necessary to make a flyer to dream of bees on the honeycomb, could leave the box.

In such a box, it is possible to keep the bees again for some time, you can catch the swarm into it. Only in this case, you need to make a double cover: one and s grid, and their other plywood. This is done so that the rose bees do not be sealed. And in winter, such a box is useful for storing sushi.

Box with frames
Box with frames

Frame Carrying Box (Ramonos) DIY

Ramconos.

Good day, friends!

Autumn is committed to its equator, but on the household apiary is still full of work. I am sure that most of you have already completed the autumn audit and in full swing leading to wintering. Our today will concern compulsory baking inventory to be kept clean and manner.

We are talking about the framework that we periodically remove from the hives for inspection, repair, pumping honey, etc. For their temporary storage, Ramakonos is ideal - so called a special box to transfer bee frames that you can buy or make it yourself, there is nothing difficult in it - you will need only material and a simple tool.

What is a box to transfer bee frames?

Box to transfer bee frames must necessarily be in the arsenal of each self-respecting beekeeper. They are used for any manipulations with the framework, in its functionality does not have to doubt. Ramakonos should be:

  1. easy and compact - most of the models are designed for simultaneous placement of 6 or 8 beeworks;
  2. convenient for carrying - that is, equipped with handles and belts;
  3. moisture and wear-resistant, which increases its life;
  4. Multifunctional - Ramakonos is often used for fishing, transfer and short-term insect content.

Dimensions of the box must correspond to the size of the poles used at the apiary. This is definitely a fate when purchasing it or independent manufacture. Below I will tell you how to make it from the priest materials. The price of Ramakonos will depend on the model you chose, so if you do not want to make a box yourself, it can always be bought in stores for apiary.

Production procedure

Before you start making, you need to determine what make a box. The best material for the manufacture of Ramcontos is plywood. Followed by:

  1. Prepare the tool and additional elements of the box - handles, loops and lock for cover, rails and self-tapping screws;
  2. pinch the components of the housing strictly in size specified on the selected drawing;
  3. combine them together by making ventilating holes;
  4. install loops and hang on them cover;
  5. attach the castle;
  6. Install pens and belts;
  7. Imprease the finished product with oil to increase its wear resistance.

Additionally, Ramakonos is recommended to equip the velocity to increase its functionality. Box to transfer bee frames, as well as any other parish inventory, it is necessary to clean and disinfect after each use. Without it, do not do during the pumping of honey and when performing other manipulations with beeworks.

"Indian Summer" is the right time to make adaptations for an apiary outdoors, so if you have such a desire, friends, I recommend making Ramconos with your own hands. He must come in handy in the future.

I have everything, I'm saying goodbye to you. Do not forget to subscribe to my blog, we have a lot of interesting topics and new information to think.

Homemade Honey Frames filled with honey

For the convenience of the health profession from the hives, the beekeepers of all over the world use various patterns of carrying or, as they are also called, Ramcontos. Do you want to get such a miracle too? To make a reliable drawer for carrying the frames with their own hands, you do not need to spend a lot of effort or means.

What should be the box?

Our box for transferred by honey frames should be quite roomy, easy, and have special belt mounts (so that it is easier to carry it in the apiary). Another requirement is an even straight cover, which will continue to use the box as a comfortable chair.

In one such drawer, 8 frames are placed (based on the suggested sizes in the drawing). It is possible to increase its capacity by correcting the sizes, but then it will be hard to transfer it. The total weight of the filled container on 8 frames will be more than 10 kg, without taking into account the weight of the structure itself. The following photo is an exemplary model of such carrying.

How to make it yourself?

To make with their own hands Ramskonos, it will take some time and, of course, the right raw material for its manufacture. Do not take heavy materials, because all this will eventually affect the weight of the finished product. Be sure to think about how your box for the framework will be closed. Take materials with a margin, you may need to make not one, but two or more products. With their help in the flow of a beekeeper, there will always be order, and the framework does not have to carry hands.

Tools and materials

  • Materials for the box will require the following: plywood sheets with a thickness of at least 4 mm, as well as rails, 45x20 mm sizes (they will bent inside and outside). Another type of material is not suitable due to the severity of the product.
  • But if you are planning a box to use and like a garden chair of a beekeeper - take the sheets of chipboard, the thickness of the product will increase in this case. We will tell about the manufacture of plywood, designed for eight frames.

  • In addition to plywood sheets and rails, self-tapping screws or thin shoal nails will also need (they are more convenient to carefully score into a subtle plywood).
  • Also need an outdoor fastening that will hold the lid so that it does not open on the go and loops for folding it. Galvanized scrap (is shown in the photo below), and for internal - ordinary small loops, two pieces.
  • And the last detail is the belt and the outer attachments for it. They are attached to the self-tapping screws, like loops inside. Mounts can be taken stainless, and the belt will buy a nylon.

To seal the box, you can stick to the thermolent over the entire internal perimeter of the cover (with a tolerance from the edge to the width of the walls - 4 mm). This thermolent is sold as a insulation for windows for the winter and there can be different thickness - we need the thinnest, about 1 mm thick. It does not concern the framework, which means it does not get dirty and will not be sticky. In addition, a sealed box for a while can be left near the hives, as it will not get free to the frame of the bee.

However, the ventilation hole at the bottom of the case can still be done so that the honey does not "hit", just be sure to close it with a small grid. The grids will need a very small piece that can be attached by the usual construction stapler.

Instructions for manufacture

So, then a step-by-step instruction for designing a box for a frame or frame carrying.

  1. In total, there are six component parts in Ramconos - it is anterior, rear and two side panels, cover and bottom. Size walls (300x330).
  2. The first one should assemble the front wall, and then rear.
  3. From the edge of the front wall from above, 15 mm retreat and nail a pre-prepared rail (length 300, width 45, height 20 - dimensions in mm). This is our future focus for the framework, that is, the folds. Such two plates are nailed from the outside - without indents.
  4. If you plan to make a vent hole in the front, you need to cut it in advance. However, many beekeepers cost them without it.
  5. The rear wall is identical to the dimensions of the front, the rails are stuffed only outside - at the top and bottom without indents from the edges.
  6. The side walls of the same dimensions (300x330) are narrowed from the front and rear, and after they are also stuffed onto their outer surface along two rails - from above and below. So it will be convenient to take a drawer in hand.
  7. Next is going to the lid, attached to the loop. Its dimensions are indicated in the drawing.
  8. The bottom is measured around the perimeter and is knocked with nails, after which the closing part of the fasten is screwed to the lid, and the stationery is fixed part of the fasten. Detailed drawings, as well as a general view of the product, can be considered further in the photo.

Thus, you will get a comfortable, tightly closing design, which can be left near the hive, without fear for the safety of collected honey.

Some frameworks of Ramakonos apply both as a trap for a roa, lubricating the bees there as a temporary dwelling. The idea of ​​such a temporary replacement of the hive drawer is pretty good. So solve yourself, whether you will also use your carrying.

Video "Box for socks frames"

Useful video in which it is described in detail how to independently assemble a multifunction box to work at the apiary.

Find out more

Features and independent manufacture of lesja

Convenient and practical Ukrainian hive

We make apilift for convenient accommodation

We make an independently portable box for frames with your own hands

Honey is not only a delicious, but also a very useful product. Today, the apiary is greatly successful. Quite often, the beekeeper appears the need to inspect the framework, so it is necessary for greater convenience, it is necessary to carry a box for carrying a frame (Ramonos). It can be bought, but make it my own hands will not be anything complicated. To do this, it is enough to have clear drawings, materials and desire to make.

Beekeeper often takes out frames from the hive

Functionality of the product

So that there were no problems with the delivery of the box from the hive, it is necessary to make it from plywood, thanks to which the framework with all the contents to get much more convenient and easier. There are 6 frames in the box. After seizures, the hive closes.

  • pick up the necessary materials and tools;
  • Think over connecting works;
  • collect elements into a single integer;
  • fasten the handles;
  • Covered by a protective composition.

The parameters of the box are small. In length from 455 mm; in width - 235 mm; In height - 320 mm.

The frames carried by the drawer are different, so after each application they need to be disinfected. Due to the accumulation of moisture on the plywood and in order to avoid the speedy wear of the product, the material is impregnated with oil. The box itself is installed near the hive or behind it, so that you can put the frames there during honey pumping. The box should be not heavy, but strong, so that during operation he has not broke.

Ten Frame Box

Production option

The size of the box, where the 6 frames will be included, the following: 470x300 mm (DHSH). Depending on the size of the frames themselves, Ramonos parameters are calculated. For example, if the width is 37 mm, then the product will have a width of 222 mm. To calculate the parameter, the width of one frame must be multiplied by their number. All side planks are better made from the board whose width is 20 mm. For the walls, take the phaneer with a thickness of 4 mm. It is attached with the help of ordinary lack of wooden wooden planks.

Appearance of the box inside

Before proceeding with the preparation of materials, it is necessary to develop a drawing with concrete sizes. . The height of the drawer for storing a frame produced by their own hands is done with a small margin of 50 mm, so the final design height is 350 mm. Experienced beekeepers are recommended to multiply by the number of frames rounded width (i.e. not 37, and 40 mm).

The length of the product will depend on the boards used, or rather from their thickness. On average, a size is taken equal to 510 mm. Thus, the carrying for the framework will have the following parameters: 510x350 mm. With the help of a screwdriver gently collect the product.

For the bottom and the lid is taken by a plywood in 4 mm thick. To cut these parts only after assembling the main sides of the frame storage box. Otherwise, it is possible to make a mistake in the calculations and not take into account the thickness of the planks used. Ultimately, the bottoms will be attached to the boards, which will make the design stronger and reliable. The cover of the product must fit tightly, so the dimensions of the planks must fully correspond to the internal perimeter of the drawer. It is there that they subsequently will be stuffed.

From both sides, the handles are screwed to the box so that it can be free to move it freely. To do this, install brackets and stretch the sling, which the node is tied after the tension. The node itself should be pushed to the brackets so that in the future it does not interfere. Make it is necessary so that you can hang the row on the shoulder. After all, sometimes the box reaches 20 kg in weight, and it is quite difficult to carry such a cargo. Frames with honey are rather heavy and sometimes reach 5 kg (the frame "Dadan").

Drawing of the box for transferring frames in transverse (A) and longitudinal cuts (b)

How do bins use in beekeeping?

In addition to the storage of the frames themselves, the design applies for other purposes. For example, for the roo content. The beekeepers consider it the best option than a special Roya, in which bees often suffer concern because of a long stay in the dark. Roy is placed directly on the frame after its withdrawal. The design itself is installed next to the hives. The uterus itself should be located directly on the frame, and others can shake on a pre-prepared lower frame. But even in such a box it is not recommended for a long time to contain insects.

MEDY BACK

Constructive feature of the box for two people is that it has several large sizes. There is placed already from 20 to 22 frames from the hive. Dimensions of such Ramonos: 900x800 mm. Such a large design can be further stored for anything. One butcher with such a box will not cope. The design itself should be very durable, so the end boards must have a good thickness. For the connection it is better to use nails. With the help of screws, side planks of the top with the walls are connected. On the side of the lower part directly to the edges of the plank is nailed. In complete with the ends the handles are attached. Workers of beekeeping farms use such structures as temporary hives.

It should be noted that it is quite simple to make the design for the content of the framework. To do this, you should have an accurate drawing and a consistent action plan. The correct approach to business will save you from many problems and will greatly relieve work. In the future, such boxes are convenient to adapt to the temporary additional hive.

Sources:

http://igorlavrenyuk.ru/podgotovka-k-vesne/ramkonos.htmlhttp://zoohoz.ru/pchelovodstvo/uli/yashhik-dlya-perenoski-mok-12151/http://roypchel.ru/pchelovodstvo/yashhik- dlya-perenoski-ramok.html

Various manipulations with frames - an integral part of beekeeping. It is possible to alleviate such actions using a special box for transferring a frame that is called Ramonos. Design can be made independently. There are certain requirements for it and operating rules.

Ramonos.

Requirements for Ramonosu

In order for Ramonos to be easily and convenient to use, the design must comply with certain requirements:

  • Ease - a heavy box will be impossible to operate, so it should be small (usually by 6-8 frames) and from lightweight material (more often);
  • Specific dimensions - they must correspond to the size of the frames used at the apiary;
  • Multifunctionality - In addition to transferring the framework, the design can be used for fishing;
  • convenience of carrying - it is necessary to provide a drawer with handles, belt;
  • Moisture resistance - such a property is ensured by impregnation with oil, it additionally increases the wear resistance of the product.

Ramonos can be used even for insect content, but only short-term. This option allows you to replace the special Roya, in the dark of which the bees are very worried.

Making a drawer for carrying frames with their own hands

Simple Ramonos.

Make Ramonos is easy. The dimensions of the design depend on the transfer of how many frames it is intended. More often performed the product on 6 frames. Its optimal length - 47 cm, width - 30 cm, height - 35 cm (always leave the supply of 5 cm). Internal parameters are calculated by the width of the used frames and their number. If the design should contain 6 frames of 3.7 cm wide, then its width inside should be 22.2 cm (6x3.7).

For the manufacture of Ramonos, we need the following materials and tools:

  • Plywood or boards - for the bottom and cover thickness 4 mm;
  • loop for cover;
  • Reiki;
  • screwdriver or drill (you can do and screwdriver);
  • Self-tapping screw;
  • Lock lock;
  • Pens and belt belt.

The manufacture of Ramonos is carried out according to the following algorithm:

  1. Put the components: front, back, ends, bottom and lid.
  2. On the inside of the front and rear wall, attach a rail - it will serve as false for the framework. 1.5 cm should be retreating from the upper edge. Both walls are manufactured by one algorithm.
  3. The side walls are also strengthened by the rails.
  4. On the lid from the inside rail to fasten around the perimeter.
  5. Connect the composite parts of the structure. The bottom is a simple piece of plywood, but if you wish, you can additionally make legs.
  6. Perform ventilation holes in the case. Their size depends on how Ramonos will be operated. Holes can be covered with a fine mesh or provide movable plugs.
  7. Connect the back of the product with a lid with a folding loop.
  8. Attach the lock to the lid.
  9. Fasten the handles and belt carrying. The belt can be mounted on the design lid, but more convenient and more reliable to use Ramonos ends for attachment. The belt-carrying should be strong enough, but it's not too tough, otherwise it will rub the shoulder.
  10. Imprease the finished product with oil. This stage, if desired, can be second, if it is more convenient to process the composite parts of the structure immediately after they are drunk.

The flyer can be performed in different ways in one of the either the front. It should be provided for a plug for the pilot. One of the convenient options is to attach two small slats on opposite sides and insert a suitable piece of plywood, which can be moved to the side.

The design of self-made Ramonos for 12 frames is presented in this video:

Ramonos for Two

For large-scale operations at the apiary, it is necessary to use a more bulk design to which 20-22 frames can fit. The dimensions of such a product are 90x80 cm. The design is quite voluminous, therefore it should be operated together.

The manufacture of Ramonos for two is carried out according to the standard algorithm, but with some features. One of them is the thickness of the material used. The design is volumetric, so its weight with the frames will be rather big. This improves requirements for used materials. You can make the basis of thick slats, and to use the plywood to use.

Connect the details of the Ramonos for two are recommended using nails. To fasten the side planks and walls can be screwed. Due to the weight and size of the design of its handles and belt, the carrying should also be increased strength.

The obligatory stage of manufacturing Ramonos for two is the impregnation of the olifa of the finished product or its component parts separately.

Rules of operation and care

Ramonos - the design is quite simple, but requiring some care:

  • Disinfection. It should be carried out after each operation of the design.
  • Carrying. To ventilate Ramonos not only before the first operation, but in the future. Bees to smells are very sensitive.
  • Before exploitation of Ramonos, it is recommended to complain its attractive herbs for bees.
  • Ramonos is a wood product, so it is necessary to store it accordingly. At the storage location should be sufficiently sufficient, strong differences of moisture and temperature should be avoided.
  • Use when roding. In this case, in Ramonos, you must put a pair of frames with dryness, and then shake the bees. The design cover and the pilots are necessarily closed. Ramonos leave in a cool place for the night. Competently organized ventilation will provide insects with the necessary air, and also reduce the temperature inside Ramonos - it acts soothing on insects.

Ramonos is often referred to as a worker or universal box. This design at the apiary is very convenient and greatly facilitates a number of works. You can make it yourself - all materials and actions are simple. Properly executed design ensures its multifunctionality.

Publication author

not online 1 year

Ilina Irina

3 Publications: 79. Comments: 0.

Добавить комментарий